WORK
AT THE END OF THE WORK
Before beginning to work, it is necessary to:
1. Carry out the operations described in the “
PREPARING TO WORK
” chapter.
2. Check that the squeegee body is in contact with the surface to be cleaned. If it isn't, turn the knob
(1) in the direction of the arrow (
Fig.1
).
N.B.
:
Fig.1
shows the left side of the device. Rotate the knob on the right-hand side in the
opposite direction.
3. Release the handlebar from its vertical position and rotate it towards you.
CAUTION
: During this operation, do not rest your foot on the machine.
4. Adjust the control handlebar.
5. Start the machine using the main switch (2) (
Fig.2
).
N.B.
: if the LED of the main switch (2) (
Fig.2
) is lit up, this means there is electrical continuity.
N.B.
: As soon as the machine starts, the front LEDs will light up and both the brush motor and
the vacuum motor will start working.
6. Activate the detergent solution supply by pressing the electric pump control switch (3) (
Fig.3
).
N.B.
: if the LED of the electric pump control switch (3) (
Fig.3
) is active, this means the pump will
supply detergent solution.
7.
The machine will now begin to work with full efficiency until the battery runs down or until the
detergent solution has finished.
N.B.
: The joint on the body of the machine provides greater manageability. To make a left-hand
turn, rotate the handle to the left (
Fig.4
); rotate it to the right when you want to turn right.
N.B.
: If you need to turn back while you are working, just rotate the machine by 180° by turning
the control handle.
N.B.
: if the handlebar is placed in the idle position (vertical) during use, the brush motor and
electric pump will stop working. After a few seconds, the vacuum motor will switch off as well.
N.B.
: if the charge level reaches a certain value during use, the brush motor and the electric
pump will stop working. After a few seconds, the vacuum motor will switch off automatically as
well. Both the LED of the main switch and that of the electric pump control switch will remain ON.
At the end of the work, and before carrying out any type of maintenance, perform the following
operations:
1.
Switch off the machine using the main switch (1) (
Fig.1
).
2. Rotate the handlebar so it is vertical.
CAUTION
: During this operation, do not rest your foot on the machine.
3.
Raise the squeegee body off the floor and rotate the knob (2) in the direction of the arrow (
Fig.2
).
N.B.
:
Fig.2
shows the left side of the machine . Rotate the knob on the right-hand side in the
opposite direction.
4.
Take the machine to the designated place for draining off the dirty water.
ATTENTION
: the place designated for this operation must comply with current environmental
protection regulations.
5. Remove the battery (3) from the battery compartment; to free the battery, shift the stop lever (4) in
the direction of the arrow (
Fig.3
).
6. Remove the battery from the battery compartment using the handle moulded on it (
Fig.4
).
7. Rotate the front carter (5) as far as it will go - do this with the aid of the handle (6) (
Fig.5
).
CAUTION:
these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
8. Remove the recovery tank (7) from the machine (
Fig.6
).
9. Remove the drain plug (8) on the recovery tank from its seat (
Fig.7
).
ATTENTION
: protective gloves should always be worn before handling detergents or acidic or
alkaline solutions, to avoid serious injury to the hands.
10. Empty the tank.
11. Insert the solution drain plug (8) into its seat on the solution tank (
Fig.8
).
12. Remove the solution tank from the machine (
Fig.9
).
13.
Remove the filling cap (9) from its seat on the detergent solution tank (
Fig.10
).
14. Empty the tank.
15. Rinse the inside of the tank with a jet of water.
16.
Replace the filling cap (9) in its seat on the detergent solution tank (
Fig.11
).
17.
Insert the two tanks in the machine, positioning first the solution tank and then the recovery tank.
18. Rotate the front carter (5) as far as the work position; do this with the aid of the handle (6) (
Fig.12
).
19. Block the handlebar in the horizontal position (
Fig.13
).
CAUTION
: During this operation, do not rest your foot on the machine.
20. Turn the stop lever of the command handlebar (10) in the direction of the arrow (
Fig.14
).
21. Close the command handlebar again, pushing the handle (11) towards the body of the machine
(
Fig.15
).
22. Turn the stop lever of the command handlebar (10) in the direction of the arrow (
Fig.16
).
23. Take the machine to the designated machine storage place.
24.
Position the machine with its rear part in contact with the floor (
Fig.17
).
WARNING
: Park the machine in an enclosed place, on a flat surface; near the machine there
must be no objects that could either damage it, or be damaged through contact with it.
11
6
5
11
10
4
2
3
1
2
3
1
ON
1
1
OFF
3
2
2
4
3
4
6
5
7
5
6
8
8
7
7
9
6
5
12
9
9
10
11
14
15
10
11
13