manualshive.com logo in svg

Trico DR-7, User Manual

Share
Download
Trico DR-7 User Manual Download Page 28

Page 28 of 28 

 

10.

 

Limited Warranty 

 

Trico warrants to the original purchase only, that these Ferrographic instruments and/or Ferrographic 

supplies, and accessories (the “Product”) are free from defect in material and workmanship and will 

remedy any such defect according to the terms of this Limited Warranty. 

 

Trico will repair (or at its option, replace) at no charge any defective component(s) of Trico’s instruments 

for twelve (12) months from date of purchase. 

 

Trico will repair (or at its option, replace) at no charge any 

defective component(s) of Trico’s supplies and accessories for ninety (90) days from date of purchase. 

 

To make request or claim for service under this Limited Warranty, the original purchaser must return the 

Product, shipping prepaid, in the original shipping container or equivalent, to Trico, after receiving return 

authorization from Trico and assuming the risk of loss or damage in transit. 

 

This Limited Warranty shall not apply if the Product has been damaged due to abuse, negligence, misuse, 

misapplication, or accident after the Product has been shipped.

 

Trico does not warranty any damage 

caused by third party or malicious software. 

 

ALL EXPRESS AND IMPLIED WARRATNTIES FOR THIS PRODUCT, INCLUDING THE 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE 

LIMITED IN DURATION TO A PERIOD OF ONE (1) YEAR FROM THE DATE OF PURCHASE 

FOR INSTRUMENTS AND NINETY (90) DAYS FOR SUPPLIES AND ACCESSORIES, AND NO 

WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THESE PERIODS. 

 

IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR 

SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED HERE.  IN NO EVENT 

WILL TRICO BE LIABLE TO YOU FOR ANY DAMAGES, INCLUDING ANY LOST PROFITS, 

LOST SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF 

THE USE OR INABILITY TO USE SUCH PRODUCT, EVEN IF TRICO HAS BEEN ADVISED OF 

THE POSSIBLITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY. 

 

This warranty gives you specific legal rights, and you may also have other rights which may vary from 

state to state.  If any provision of this Limited Warranty is held to be unenforceable for any reason, it shall 

be modified rather than voided, if possible, to achieve the intent of the parties.  In such an event, all 

provisions of this Limited Warranty shall be deemed valid and enforceable to the full extent. 

 

 

 

 

 

 

Trico Corporation 

1235 Hickory Street 

Pewaukee, WI 53072 

800.558.7008 or 262.691.9336 

www.tricocorp.com

 

Summary of Contents for DR-7





























Reviews:

No comments

Brands by name

Popular brands

Load more brands