manualshive.com logo in svg

Trico DR-7, User Manual

Share
Download
Trico DR-7 User Manual Download Page 16

Page 16 of 28 

 

7.1.3 – MENU Button  

The MENU button is in the upper right corner of the RUN DR tab. By pressing this button, the DR-7 

settings menu appears in the Submenu Selection area. Different settings can be selected from the pull-

down menu to control beep on key hit, if a control number is required per sample before testing, and the 

number of pump revolutions to start suction during a test. 

 

 

Selections can be made by touching the desired setting pull down and hitting the up or down arrows to the 

side to scroll through the selections. After all changes are made press the SAVE & EXIT button to set the 

new selections and then exit to exit out of the menu. Default settings are, Beep on key hit: No, Control 

number required: No, Pump revolutions: 2. 

 

 

7.1.4 –Shutdown Procedures 

To close the DR-7 program and exit to Windows, enter the MENU Screen under the RUN DR Tab and 

press the EXIIT button. In doing this the user enters the Windows Desktop screen. Here is all of the 

functions of a normal Windows based operating system. To shut down the power fully, either use the 

shortcut on the desktop, or go to the start menu and click on shutdown to close the operating system. This 

may take a few seconds to close windows applications and fully shut down. 

 

Once the operating system is fully shut down and the touch screen turns black the user may flip the rocker 

switch on the back of the unit to the “OFF” position. By turning the power off, the illuminated Trico logo 

will dim to black. 

 

 

Summary of Contents for DR-7





























Reviews:

No comments

Brands by name

Popular brands

Load more brands