background image

4.  Press the + or - button until the desired “DHW Set

Value”  setting  is  achieved.    Press  STORE  to  save
the setting.  The display will flash when the revised
setting is accepted.

5.  Once  the  desired  parameter  setting  have  been

revised  and  stored  within  the  PRESTIGE  Control
module, press RESET to exit the CODE mode.

The performance specifications listed are based on
a DHW set value setting of 46

º

F. A setting other than

the factory setting of 46

º

F will effect the actual per-

formance of the water heater.

DHW DETECTION ON PARAMETER

The MCBA Control Module has 2 differential settings for
the  burner  operation  when  using  the  IDWH  Sensor
parameter  setting.  The  first  differential  setting  the
installer  has  the  option  of  adjusting  is  Parameter  38
“Detection ON”.  This parameter sets the DHW storage
temperature low limit.  The burner operation will respond
when  the  DHW  storage  temperature  drops  below
Parameter 1 setting minus Parameter 38 setting.

A minimum “Detection ON” parameter setting will create
a  quicker  burner  operation  response  to  any  domestic
water draws from the water heater.  In contrast, a maxi-
mum  “Detection  ON”  setting  will  result  in  a  delay
response to domestic draws.

To  achieve  the  performance  specification  listed  for
this water heater, it is recommended the factory set-
ting of 18

º

F be revised to 2

º

F.

The  “Detection  ON”  setting  of  Parameter  38  greatly
affects the production of domestic hot water.  A min-
imum setting of Parameter 38 could result in a rapid
response  to  a  DHW  request  for  heat  resulting  in  a
potential scald hazard.  It is strongly recommended
that the installer utilize a anti-scald thermostatic mix-
ing valve on the hot water outlet of the water heater.
Failure  to  comply  could  result  in  severe  personal
injury, death or substantial property damage.

DANGER

NOTICE

NOTICE

IDWH Sensor Parameters

14

To  revise  the  parameter  setting  within  the  PRESTIGE
Control  Module  for  DHW  “Detention  ON”  control,  the
installer  must  activate  the  access  code  for  the  control
module as previously described in the Program Access
of the MCBA section on page 10.

1.  Enter into the access code mode.

2.  Once  the  access  code  has  been  entered  and

accepted,  press  MODE  until  the  display  shows

PARA

.

3.  Press  STEP  until  the  display  shows 

P_38

.    This

parameter  setting  is  the  Detection  ON  parameter.
After  releasing  the  STEP  button  the  display  will
show the current setting.

4.  Press  the  +  or  -  button  until  the  desired  DHW

“Detection  ON”  setting  is  achieved.    Press  STORE
to save the setting.  The display will flash when the
revised setting is accepted.

5. Once  the  desired  parameter  settings  have  been

revised  and  stored  within  the  PRESTIGE  Control
module, press RESET to exit the CODE mode.

DHW DETECTION OFF PARAMETER

The  second  differential  setting  is  Parameter  39
“Detection OFF”.  This parameter sets the DHW storage
temperature high limit.  The burner operation will cease
when  the  DHW  temperature  rises  above  Parameter  1
plus Parameter 39.

A maximum “Detection OFF” parameter setting will result
in  an  extended  burner  firing  cycle  when  responding  to
any domestic water draws from the water heater.  This
extended burner firing cycle could result in a final tem-
perature of the domestic hot water that is higher than the
desired temperature setting.

To achieve the performance specifications listed for
this water heater, it is recommended the factory set-
ting of 0

º

F be revised to 8

º

F.

NOTICE

Summary of Contents for MiniSmart
























Reviews: