manualshive.com logo in svg

TriangleTube Delta, Installation And Maintenance Manual

Share
Download
TriangleTube Delta Installation And Maintenance Manual Download Page 49

43

Start-Up Procedures

Accessing Control Information 

Information Mode  

To switch from STANDBY mode to INFOR-
MATION mode, press MODE twice.
Press STEP until the system displays the infor-
mation you need. The point located behind the
first position flashes to indicate that the appli-
ance is in INFO mode.

Note :

The last three digits on the display is

the measured or calculated temperature or rate
of increase and is shown in the manual with 

[

[-

--

--

-]

].

.

If STEP is pressed after parameter 9, the dis-
play will show

A-32

.

NFO

I

Measured CH outlet (supply) water
temperature

Measured CH inlet (return) water 
temperature
Measured DHW storage 
temperature

Measured outdoor temperature

(Optional outdoor sensor required)

1
2

-

-

---

--

--

---

3
4

STEP

STEP

STEP

STEP

This parameter is not used

-22

5

STEP

Key:

Display

Description of parameters

Rate of increase in the outlet water
temperature  F/sec

Rate of increase in the return water
temperature  F/sec

Rate of increase in the DHW 
temperature  F/sec

6
7

---

---

---
---

8
9

STEP

Calculated (target) outlet water 
temperature

STEP

STEP

STEP

ARA

P

MODE

NFO

I

MODE

Key:

Display

Pressing MODE once

Pressing MODE twice

Summary of Contents for Delta

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands