manualshive.com logo in svg

TriangleTube Delta, Installation And Maintenance Manual

Share
Download
TriangleTube Delta Installation And Maintenance Manual Download Page 28

Gas Piping

SECTION V - Gas Piping

Gas Supply Piping Connection

The gas supply piping must be installed

in accordance to all applicable local,

state and national codes and utility

requirements.

1. Refer to Fig. 11 to pipe gas supply to the

burner.

a. Install a pipe nipple and union at the

factory supplied 3/4” NPT gas cou-
pling, for ease of service.

b.  Install a manual shutoff valve in the gas

supply piping as shown in Fig. 11.  For
installations in Canada, the installer
must tag and identify the main shutoff
valve.

c.  Install a drip leg on the gas supply line

prior to connecting to the MODULAT-
ING DELTA gas train as shown in Fig.
11.

2.  Support the gas piping using hangers.  Do

not support the piping by the appliance or
its components.

3.  Purge all air from the gas supply piping.

4.  Before placing the MODULATING

DELTA into operation, check and test all
connections for leaks.

Close the manual shutoff valve during
any pressure test with less than 13”w.c.. 

Disconnect the MODULATING
DELTA and its gas valve from the gas
supply piping during any pressure test
greater than 13”w.c..

Do not check for gas leaks with an open

flame.  Use a gas detection device or bub-

ble test.  Failure to check for gas leaks

can cause severe personal injury, death

or substantial property damage.

5.  Use pipe dope compatible with natural and

propane gases.  Apply sparingly only to the
male threads of pipe joints so that pipe
dope does not block gas flow.

Failure to apply pipe dope as detailed

above can result in severe personal

injury, death or substantial property

damage.

Use a two-wrench method of tightening

gas piping near the appliance and its gas

valve.  Use one wrench to prevent the gas

valve line connection from turning and

the second to tighten adjacent piping.

Failure to support the gas valve connec-

tion piping could damage the valve and

the gas line components.

WARNING

WARNING

WARNING

NOTICE

22

External Manual

 Shutoff valve

(must be within 6' 

from the water heater)

Tee

Pipe Cap

Drip leg

Burner gas train

Male union

Pressure gauge port

(1/8" NPT plugged)

Direction of flow

3" Minimum

Fig. 11: Recommended Gas Supply Piping

Summary of Contents for Delta

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands