manualshive.com logo in svg

TriangleTube Delta, Installation And Maintenance Manual

Share
Download
TriangleTube Delta Installation And Maintenance Manual Download Page 40

34

Start-Up Preparation

3.  Fill the outer tank to correct system pres-

sure.  Correct pressure will vary with each
application.

Typical residential system fill pressure is

12 psi.  System pressure will increase

when system temperature increases.

Operating pressure of the system should

never exceed 25 psi.

4.  Allow air to escape from the outer tank by

opening the automatic air vent provided
with the MODULATING DELTA.

5.  Purge air in each zone of the primary sys-

tem through the purge valve.  Open air
vents to allow air to be purged in the zones.

6.  Once the system is completely filled and

purged of all air, check the system pressure
and check for leaks.

Check For Gas Leaks

Prior to start-up and during initial opera-

tion, smell near the floor and around the

appliance for gas odorant or any unusual

odor. Do not proceed with the start-up if

there is any indication of a gas leak.  Any

leaks found must be repaired immediate-

ly.

DO NOT adjust or attempt to measure

gas valve outlet pressure.  The gas valve

is factory-set for the correct outlet pres-

sure.  This setting is suitable for natural

gas and propane and requires no field

adjustment.  Attempts by the installer to

adjust or measure the gas valve outlet

pressure could result in damage to the

valve, causing potential severe personal

injury, death or substantial property

damage.

Propane installations only - The propane

supplier mixes an odorant with the

propane to make its presence detectable.

In some cases the odorant can fade and

the gas may no longer have an odor.
Prior to start-up of the appliance and

periodically after start-up, have the

propane supplier check an verify the

odorant level.

Check Thermostat Circuit

-

Disconnect the external thermostat
wires from terminals 7 and 8 on the low
voltage terminal strip.

-

Connect a voltmeter across the wire
ends of the external thermostat wiring.

-

Close each thermostat, zone valve and
relay in the external circuit one zone at
a time and check the voltage reading
across the wire ends.

-

There should 

NEVER

be voltage mea-

sured at the wire ends.

-

If voltage is measured at the panel
under any condition, check and correct
the external wiring.

In systems using 3-wire zone valves

backfeed of voltage to the appliance is a

common problem.  Use an isolation relay

to prevent voltage from the external cir-

cuit entering the MODULATING

DELTA control panel.

NOTICE

WARNING

WARNING

WARNING

NOTICE

Summary of Contents for Delta

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands