EN - T18S/R14
-21-
WARNING:
Do not tighten the collet
without a cutter fitted.
WARNING:
Always use cutters with
shanks which match the diameter of the collet.
WARNING:
Deep cuts should always be
routed in several passes.
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Plunge Locking Lever on
the Plunge Base - (Fig. 7)
• Excessive force should not be used to clamp the
locking lever. Using excessive force may damage the
base.
• Push lever down to lock.
• When the locking lever is clamped, the motor should
not move in the base.
• Adjustment is needed if the locking lever will not clamp
without excessive force or if the motor moves in the
base after clamping.
Centring the Slider on the
Plunge Base - (Fig. 8 – 8a)
• If you need to adjust, change, or replace a subbase,
a centring tool is recommended. The centring tool
consists of a cone and a pin.
To adjust a slider follow the steps below.
• Fit guide bush to slider plate.
• Loosen but do not remove the slider screws so the
slider moves freely.
• Insert the pin into the collet and tighten the collet nut.
• Insert the motor body into the base and clamp the
locking lever on the base.
• Place the cone on the pin and lightly press down on
the cone until it stops. This will centre the subbase.
• While holding down on the cone, tighten the subbase
screws.
• See Fitting the Guide Bush to the Plunge Base and
Trim Base (Fig. 12).
Centring the Slider on the
Trim Base - (Fig. 9)
• If you need to adjust, change, or replace a subbase,
a centring tool is recommended. The centring tool
consists of a cone and a pin.
To adjust a slider follow the steps below. With or without
the guide bush fitted.
• Loosen but do not remove the slider screws so the
slider moves freely.
• Insert the pin into the collet and tighten the collet nut.
• Insert the motor body into the base and clamp the
locking lever on the base.
• Place the cone on the pin and lightly press down on
the cone until it stops. This will centre the subbase.
• While holding down on the cone, tighten the subbase
screws.
• See Fitting the Guide Bush to the Plunge Base and
Trim Base (Fig. 12).
Installing and Removing Parallel
Side Fence on the Plunge Base
- (Fig. 10)
A parallel side fence is supplied with the guide rods
fitted.
• Loosen the thumb knobs on the plunge base.
• Slide the parallel side fence with rods fitted into the
plunge base holes.
• Tighten the thumb knobs temporarily to lock the fence
in position.
• To remove the parallel side fence, loosen the thumb
knobs and pull the parallel side fence out if the plunge
base.
Installing and Removing Parallel
Side Fence on the Trim Base
- (Fig. 11 – 11a)
• Assemble the straight guide with the bolt and the knob.
• Attach the straight guide to the trimmer base with the
trim base parallel side fence locking knob.
Fitting the Guide Bush to the
Plunge Base and Trim Base - (Fig. 12)
The guide bush allows for repetitive cut with template
patterns by using a template.
• Place the guide bush into the recess on the underside
of the base, and then secure the guide bush with the
two fixing screws.
Summary of Contents for T18S/R14
Page 6: ...T18S R14 6 1 2 1 2 Fig 12 Fig 13a Fig 13b Fig 14 Fig 13 Fig 13c...
Page 7: ...T18S R14 7 M6 115mm 15mm 1 2 figure 18 1 Fig 15 Fig 20 Fig 20a Fig 17 Fig 18 Fig 19 Fig 16...
Page 8: ...T18S R14 8 2 2 1 figure22 1 2 Fig 20c Fig 20b Fig 21 Fig 22 1 2 3 4...
Page 10: ...T18S R14 10 figure26b Fig 26b Fig 27...
