manualshive.com logo in svg

Traxxas 53097-3, Owner'S Manual

The Traxxas 53097-3 is an extraordinary remote-controlled car that guarantees thrilling adventures for hobbyists. Unlock the full potential of your Traxxas 53097-3 with the detailed and comprehensive Owner's Manual. Download this invaluable manual for free from our website to discover all the features and optimize your driving experience.

Share
Download
background image

Page 6

 

   Revo: TRX 3.3, TQi 2.4GHz Radio System, Traxxas Link Wireless Module, & TSM (Model 53097-3) Parts List 

REV. 180118 1408 

5385 

Gear set, 2-speed standard ratio (2nd speed gear 39T, 13T-17T 
input gears, hardware) 

 

5384 

Gear set, 2-speed wide ratio (2nd speed gear 38T, 13T-18T input 
gears, hardware) 

 

5386 

Gear, 1st speed, 43T   

5414X 

Gear, center differential (Revo)/ X-ring seals (2)/ gasket (1) 
(Replacement gear for 5414) 

 

5416 

Gear, differential output (Revo center diff, front or rear without 
rear brake kit (5417))   

5415 

Gear, differential output (Revo center diff, rear with rear brake kit 
(5417))  

5377 

Gear, idler/ idler gear support/ bearing (pressed in) 

 

5391R 

Gearbox halves (front & rear)/ rubber access plug/ shift detent ball/ 
spring/ 4mm GS/ shift shaft seal, glued 

 

5366 

Input shaft, transmission (slipper shaft) 

 

5368 

Linkage set, throttle & brake, Revo-Slayer (includes servo horns, rod 
guides, brake spring, brake adjustment dial, brake lever, rods (wires), 
bellcrank, throttle return spring, hardware) 

 

5392 

Linkage, shift, Revo (includes: ball collar, spring, ball cup, servo horn, 
linkage wire) 

 

5398 

OptiDrive electronic shift module   

5397 

OptiDrive sensor assembly/ 2.5x6mm CS (2)   

5395 

Output gears, forward & reverse/ drive dog carrier 

 

5369 Output 

shaft, 

transmission   

5390 

Primary clutch assembly/ 2x9.8mm pin/ 6x8x0.5 TW (1)   

5396X 

Primary gears, forward and reverse/ 2x11.8mm pin/ pin retainer/ disc 
spring  

5393 

Primary shaft/ 1st speed hub/ one-way bearing/ snap ring/ 5x8mm 
TW  

3982 PTFE-coated 

6x8x0.5 

(10)   

5352R 

Rebuild kit (heavy duty), slipper clutch (steel disc/ aluminum 
friction pads (3)/ spring, Revo (1)/ spring, Maxx (1)/ 2x9.8mm pin/ 
5x8mm MW/ 5.0mm NL (1)/ 4.0mm NL (1))   

5395X 

Reverse installation kit (includes all components to add 
mechanical reverse (no Optidrive) to Revo) (includes 2060 sub-
micro servo) 

 

5389X 

Shift fork/ shaft 

 

Turnbuckles & Threaded Rods 

5477 

Flat wrench, 5mm (blue-anodized aluminum)   

5339 

Insert, threaded steel (replacement inserts for Tubes) (includes 
(1) left and (1) right threaded insert) 

 

5341 

Linkage, steering (Revo 3.3) (3x50mm Turnbuckle) (2)/ rod ends 
(short) (4)/ hollow balls (4) 

 

5319X 

Push rod (aluminum) (assembled with rod ends) (2) (red) (use 
with #5359 progressive 3 rockers) 

 

5318X 

Push rod (aluminum) (assembled with rod ends) (2) (use with 
long travel or #5357 progressive-1 rockers)  

5319 

Push rod (steel) (assembled with rod ends) (2) (black) (use with 
#5359 progressive 3 rockers) 

 

5318 

Push rod (steel) (assembled with rod ends) (2) (use with long travel or 
#5357 progressive-1 rockers) 

 

5338 

Toe link, 5.0mm steel (front or rear) (2) 

 

5338A 

Toe links, Revo (Tubes 7075-T6 aluminum, black) (128mm, fits 
front or rear) (2)/ rod ends, rear (4)/ rod ends, front (4)/ wrench (1)
 

 

5338R 

Toe links, Revo (Tubes red-anodized, 7075-T6 aluminum, 
stronger than titanium) (128mm, fits front or rear) (2)/ rod ends, 
rear (4)/ rod ends, front (4)/ aluminum wrench (1) 

 

Two-Speed Components 

5119 

Ball bearings, blue rubber sealed (10x15x4mm) (2) 

 

5116 

Ball bearings, blue rubber sealed (5x11x4mm) (2) 

 

5117 

Ball bearings, blue rubber sealed (6x12x4mm) (2) 

 

5383 

Gear set, 2-speed close ratio (2nd speed gear 40T, 13T-16T input 
gears, hardware) 

 

5385 

Gear set, 2-speed standard ratio (2nd speed gear 39T, 13T-17T 
input gears, hardware) 

 

5384 

Gear set, 2-speed wide ratio (2nd speed gear 38T, 13T-18T input 
gears, hardware) 

 

5386 

Gear, 1st speed, 43T   

5390 

Primary clutch assembly/ 2x9.8mm pin/ 6x8x0.5 TW (1)   

5396X 

Primary gears, forward and reverse/ 2x11.8mm pin/ pin retainer/ disc 
spring  

5393 

Primary shaft/ 1st speed hub/ one-way bearing/ snap ring/ 5x8mm 
TW  

 

If you have questions or need technical assistance, call Traxxas at: 

1-888-TRAXXAS 

(1-888-872-9927) (U.S. residents only)

 

 

For orders, calls outside the U.S., and other information, call 972-549-3000,  

or fax to 972-549-3011 e-mail Traxxas at [email protected]

 

T R A X X A S . c o m

 

Summary of Contents for 53097-3




























































Reviews:

No comments

Related manuals for 53097-3

Jamara Mercedes-AMG GT R Instructions Manual preview
Mercedes-AMG GT R
Brand: Jamara Pages: 20
FG Modellsport 10007 Mounting Instruction preview
10007
Brand: FG Modellsport Pages: 28
Team Losi Audi R8 LMS Ultra FIA-GT3 AWD RTR Owner'S Manual preview
Audi R8 LMS Ultra FIA-GT3 AWD RTR
Brand: Team Losi Pages: 6
MODSTER MINI CITO User Manual preview
MINI CITO
Brand: MODSTER Pages: 27
Eduard M1070 & M1000 w/D9R Quick Start Manual preview
M1070 & M1000 w/D9R
Brand: Eduard Pages: 4
PR RACING 77500256 Manual preview
77500256
Brand: PR RACING Pages: 28
Serpent Spyder SRX2 SC Instruction Manual preview
Spyder SRX2 SC
Brand: Serpent Pages: 36
Kaylee KL-20039 Assembly And Safety Instructions preview
KL-20039
Brand: Kaylee Pages: 5
HOMCOM 370-204V90 Assembly Instruction Manual preview
370-204V90
Brand: HOMCOM Pages: 29
Carson DNA Warrior Brushless 500404092 Instruction Manual preview
DNA Warrior Brushless 500404092
Brand: Carson Pages: 44
Dynacraft Avengers Owner'S Manual preview
Avengers
Brand: Dynacraft Pages: 28
Jamara 460203 Instruction preview
460203
Brand: Jamara Pages: 12
Amewi 22395 Instruction Manual preview
22395
Brand: Amewi Pages: 32
Jamara 404980 Instruction preview
404980
Brand: Jamara Pages: 8
Peg-Perego POLARIS RANGER RZR 900 Use And Care Manual preview
POLARIS RANGER RZR 900
Brand: Peg-Perego Pages: 14
Hobbico KRATON Instruction Manual preview
KRATON
Brand: Hobbico Pages: 76
Tameo Kits TMK 215 Assembly Manual preview
TMK 215
Brand: Tameo Kits Pages: 2
Tameo Kits Ferrari F92A Manual preview
Ferrari F92A
Brand: Tameo Kits Pages: 4

Brands by name

Popular brands

Load more brands