Traxxas 53097-3 Owner'S Manual Download Page 50

Page: 50 / 59

Page 2

Revo: TRX 3.3, TQi 2.4GHz Radio System, Traxxas Link Wireless Module, & TSM (Model 53097-3) Parts List

REV. 180118 1408

5414X

Gear, center differential (Revo)/ X-ring seals (2)/ gasket (1)
(Replacement gear for 5414)

5416

Gear, differential output (Revo center diff, front or rear without
rear brake kit (5417))

5415

Gear, differential output (Revo center diff, rear with rear brake kit
(5417))

5380

Housings, differential (front & rear) (1)

5130

Oil, differential (100K weight) (.7 oz (20cc))

5135

Oil, differential (10K weight)

5136

Oil, differential (30K weight)

5039

Oil, differential (500K weight)

5137

Oil, differential (50K weight)

5379X

Ring gear, differential/ pinion gear, differential

5379R

Ring gear, differential/ pinion gear, differential (machined, spiral
cut) (front)

5381X

Spool, differential (eliminates differential. Use off-road only)
(requires #5379X ring gear)

Driveline Components

5334R

Axle carriers, left & right (1 each) (use with larger 6x13mm ball
bearings)/ bearing adapters (for 6x12mm ball bearings) (2)/ dust boot
retainers (4)

5459

Boots, driveshaft (rubber) (2)

5153R

Drive cups, inner (2) Revo (steel constant-velocity
driveshafts)/screw pin, M4/15(2) (for use only with 5333R
adjustable wheelbase rear suspension arms)

5153

Drive cups, inner (2) Revo/Maxx (steel constant-velocity
driveshafts)/screw pin, M4/15(2)

5451X

Driveshaft assembly (1), left or right (fully assembled, ready to install)/
4x15mm screw pin (1)

5154

Driveshaft, steel constant-velocity, Revo/Maxx (shaft only,
128.5mm)/ drive cup pin (1)

5451R

Driveshafts, Revo/Maxx (steel constant-velocity)(assembled
w/inner & outer dust boots) (for models w/sealed pivot ball
suspension & 3.8'' wheels)(4)

5150

E-clips, 1.5mm (24)

5450

Half shaft set, left or right (plastic parts only) (internal splined half
shaft/ external splined half shaft/ rubber boot) (assembled with glued
boot) (2 assemblies)

5455

Half shafts, center front (internal splined (1)/ external splined (1)/
center rear (internal splined (1)/ external splined (1)) (plastic parts
only)

5456

Half shafts, center front (Revo 3.3) (internal splined (1)/ external
splined (1)/ center rear (internal splined (1)/ external splined (1))
(plastic parts only)

4955

Pins, axle (2.5x12mm) (4)

5129

Rebuild kit (for Revo/Maxx steel constant-velocity driveshafts)
(includes pins, dustboots, & lube for 2 driveshafts assemblies)

5145

Screw pin, 4x15mm (6)

5189

Screw pins, 4x13mm (with threadlock) (4)

5454

Stub axle (steel) (2)

5166

Stub axle, (1)/ axle sleeve (1) Revo/Maxx (steel constant-velocity
driveshaft)

5452

U-joints, driveshaft (carrier (4)/ 4.5mm cross pin (4)/ 3mm cross pin
(4)/ e-clips (20)) (metal parts for 2 driveshafts)

5353X

Wheel hubs, splined, 17mm (blue-anodized) (4)/ wheel nuts, splined,
17mm (blue-anodized) (4)/ screw pins, 4x13mm (with threadlock) (4)

5353G

Wheel hubs, splined, 17mm (green-anodized) (4)/ wheel nuts,
splined, 17mm (blue-anodized) (4)/ screw pins, 4x13mm (with
threadlock) (4)

5353R

Wheel hubs, splined, 17mm (red-anodized) (4)/ wheel nuts,
splined, 17mm (red-anodized) (4)/ screw pins, 4x13mm (with
threadlock) (4)

5353

Wheel nuts, splined, 17mm (blue-anodized) (4)

5353A

Wheel nuts, splined, 17mm (green-anodized) (4)

5457

Yoke, brake (1)/ torque pins (2)/ 4x15mm screw pin

5458X

Yokes, differential and transmission (2)/ 4x15mm screw pins (2)

5453

Yokes, stub axle (2)/ pins (2)

Engine & Servo Mounts

5360X

Big block Installation kit (engine mount and required hardware)

5361

Chassis brace, Revo (3mm 6061-T6 aluminum) (blue-anodized)/
4x16mm BCS

5360

Engine mount (complete assembly)/ 3x28mm CS with washers (2)/
3x10 CS with washers (10)

3159

Screws, 3x10mm caphead machine (hex drive) (6)/ lockwashers (6)/
hex wrench

5325R

Servo mount, throttle/ 4x10mm BCS (2)

5326

Servo mounts, steering (2)

Engine Components

5238R

Cooling head, PowerTune (machined aluminum, blue-anodized) (TRX
3.3), head protector (1), 3x6mm CCS (5)

5270R

EZ-Start 2, complete system with controller, drive unit, wiring harness

3980

Glow plug wrench (universal wrench)

3232X

Glow plug, super-duty (long-medium)/gasket

5228

Head protector, cooling head (1)/3x6mm CCS (5) (TRX 3.3)

5290

Piston/sleeve (matched set), wrist pin clips(2) (TRX 3.3)

5211R

Roller clutch/ 6x8x0.5 TW (1) (also called one-way bearing) (TRX 2.5,
2.5R, 3.3)

5277

Shaft, starter (TRX 2.5, 2.5R, 3.3)

5170 Starter,

recoil (complete with screws) (TRX 2.5, 2.5R, 3.3)

Exhaust

3155

Cable ties, medium (black) (6)

5346

Hanger, metal wire (for tuned pipe)/ 4mm GS (1)/ 4x10 BCS (1)

5254

Header spring/ gaskets (TRX 2.5, 2.5R, 3.3)

5340

Header, exhaust (tubular aluminum, silver-anodized) (TRX 2.5, 2.5R,
3.3)

5340X

Header, exhaust (tubular aluminum, silver-anodized)/ spring
mount (TRX 2.5, 2.5R 3.3)

5256

O-ring, header 12.2x1mm (TRX 2.5, 2.5R, 3.3)

5245X

Pipe coupler, molded (black)/ exhaust deflecter (rubber, black)/
cable ties, long (2)/ cable ties, short (2)

5245

Pipe coupler, molded (blue)/ exhaust deflecter (rubber, blue)/ cable
ties, long (2)/ cable ties, short (2)

5142

Screws, 3x15mm cap-head machine (hex drive) (with split and flat
washers) (6)

5342

Tuned pipe, aluminum, blue-anodized (dual chamber with
pressure fitting)/ 4mm GS

5493

Tuned pipe, Resonator, R.O.A.R. legal (dual-chamber, enhances mid
to high-rpm power) (for Revo and Slayer with TRX Racing Engines)

5490

Tuned pipe, Resonator, R.O.A.R. legal (single-chamber,
enhances low to mid-rpm power) (for Revo & Slayer with TRX
Racing Engines)

EZ Start 2 & Related parts

4579X

Connector, wiring harness (EZ-Start and EZ-Start 2)

5280

Control box (complete) (EZ-Start 2)

5281

Control box battery cover w/ belt clip (EZ-Start 2)

5273

Cush-drive elements (4) (EZ-Start 2)

5270R

EZ-Start 2, complete system with controller, drive unit, wiring harness

5276

Gear set (complete) (EZ-Start 2)

5148 Grease,

white

lithium

5275

Housing set (inner, outer)/ 3x12mmBCS (5)/ 3x20BCS (1)/ motor
bushing (EZ-Start 2)

4581X

Lead wire, glow plug (blue) (EZ-Start and EZ-Start 2)/ molex pin
extractor (use where glow plug wire does not have bullet connector)

5279

Motor/ pinion gear/ motor bushing (EZ-Start 2)

5211R

Roller clutch/ 6x8x0.5 TW (1) (also called one-way bearing) (TRX 2.5,
2.5R, 3.3)

5169

Screws, 2.6x8mm countersunk machine (6)

5282

Screws, 3x12mm button-head machine (6) (starter attachment screws
with Threadlock)

2578

Screws, 3x12mm button-head machine (hex drive) (6)

5277

Shaft, starter (TRX 2.5, 2.5R, 3.3)

5317

Wire clips, chassis (4)/ wire clip (1)/ Shock mounts (front & Rear)/
3x32mm CS (4)

Front Suspension

5334R

Axle carriers, left & right (1 each) (use with larger 6x13mm ball
bearings)/ bearing adapters (for 6x12mm ball bearings) (2)/ dust boot
retainers (4)

5323

Bulkhead tie bars, front & rear (blue-anodized aluminum)

5323R

Bulkhead tie bars, front & rear (red-anodized aluminum)

5330

Bulkhead, front (L&R halves)/ diff retainer/ 4x14mm BCS (4)

5134

Caster spacers (4)/ shims (4)

5339

Insert, threaded steel (replacement inserts for Tubes) (includes
(1) left and (1) right threaded insert)

5495

Linkage, front sway bar (Revo/Slayer) (3x70mm turnbuckle) (2)
(assembled with rod ends, hollow balls and ball stud)

5378X

Pivot ball caps (4)/ dust boots, rubber (4)/ dust plugs, rubber (4)/ dust
boot retainers, black (4), blue (4) (2 pkgs. req. to complete truck)

4933

Pivot balls (4)/ pivot ball cap bushings (4)

4933X

Pivot balls, hard-anodized 7075-T6 aluminum (4)/ pivot ball cap
bushings (4)

5319X

Push rod (aluminum) (assembled with rod ends) (2) (red) (use
with #5359 progressive 3 rockers)

5318X

Push rod (aluminum) (assembled with rod ends) (2) (use with
long travel or #5357 progressive-1 rockers)

5319

Push rod (steel) (assembled with rod ends) (2) (black) (use with
#5359 progressive 3 rockers)

5318

Push rod (steel) (assembled with rod ends) (2) (use with long travel or
#5357 progressive-1 rockers)

5354X

Rocker arm post (aluminum) (4)

5354

Rocker arm post (steel) (2)

5356

Rocker arm set, long travel (120-T) (use with #5318 or #5318X
pushrod)

Summary of Contents for 53097-3




























































Search results

Summary of Contents for 53097-3

Reviews:

Related manuals for 53097-3

Brands by name

Popular brands

Traxxas 53097-3, Owner'S Manual

Search results

Summary of Contents for 53097-3

Reviews:

Related manuals for 53097-3

Brands by name

Popular brands