manualshive.com logo in svg

Travis Industries 2003 ROF, Owner'S Manual

Share
Download
Travis Industries 2003 ROF Owner'S Manual Download Page 28

28

 Maintenance 

© Travis Industries 

4030407

 100-01146 

Replacement Parts List 

 

 ADJUSTABLE SPOUT   

100-06006  

 BURNER ASS'Y, B30 (R.O.F.)   

226-30001  

 BURNER BOTTOM A 20 GA 304 SS - 17.264 dia   

210-11189  

 BURNER CAP/PILOT SHLD ASS'Y - B30 (RING OF FIRE)   

226-30003  

 BURNER SIDE/SPACER ASS'Y, B30 (RING OF FIRE)   

226-30002  

 BURNER, TUBE - B30 (R.O.F.) STAINLESS STEEL RING, 16" o.d.  

172-01104  

 CABLE CLAMPS, NYLON 1/2" dia WHITE   

100-00143  

 CONNECTOR, COMPRESSION (MALE) 1/4" od x 1/2MPT   

100-05516  

 CONNECTOR, ROMEX   

100-00124  

 CONTROL BOARD ASS'Y, ROF   

228-30043  

 CONTROL MODULE (CIRCUT BOX) - RING OF FIRE   

100-00274  

 DIVERTER VALVE, R.O.F.   

100-06005  

 FAN, CONV, MOUNT GROMMETS (4)#w/BRS SPACERS,97  

93005017  

 FILTER, WATER PUMP - R.O.F.   

100-06004  

 FLARE ADPTR, 3/4"od x 1/2"MPT (VALVE INLET CONNECTION)   

100-05119  

 FLEX PIPE, 7/8"od x 48" - (1/2"I.D.) w/ 5/8" FITTING   

100-05118  

 FLEX ROPE LIGHT, 1/2" 110VAC, w/END CAP & POWER CORD  

100-00271  

 FLEX ROPE LIGHT, END CAP   

100-00272  

 FLEX ROPE LIGHT, POWER CORD - WITH CONNECTOR   

100-00273  

 GROMMET, PLSTC SLEEVED (LIGHT-CORD) - 1" x 17/32"   

100-02824  

 GROMMET, PLSTC SLEEVED (PWR - CORD) - 7/8" x 1/2"   

100-02823  

 HOSE CLAMP, WORM DRIVE (SS) 5/16 BAND, 1/2-29/32 CLMP RNGE  

100-06019  

 HOSE, CLEAR PVC - 1/2"id x .060 wt - 50 ft/ROLL   

100-06018  

 HW PACK, LP CONV - R.O.F. #325   

225-10325  

 IGN. CONTROL UNIT, NON-LOCKOUT   

100-05513  

 LOCK-NUT, 1/2" STEEL   

100-06015  

 MANUAL, RING OF FIRE 2003   

100-01146  

 MINI FLOAT VALVE WITH 1/4" - TUBE INLET & ADJUSTABLE FLOAT   

100-06010  

 NEOPRENE WASHER   

100-06020  

 OBS per BA 5-8-03, SEE 5102 BURNER INNER SHIELD   

210-11191  

 OBSOLETE - 91500561 GLASS BEADS, 3/4"dia - MULTI-   

100-06017  

 ORIFICE S-ASS'Y, RING OF FIRE   

226-40023  

 ORIFICE, BURNER - 3/16" 1.180 BRS HEX (.187)   

100-05220  

 ORIFICE, BURNER - No. 37 # 1.180" BRASS HEX (.104 dia) 

100-05204  

 ORIFICE, PILOT - .016 #   

100-05216  

 OUTER SCREEN S-ASS'Y, ROF   

220-00072  

 PILOT ASSY, NG RS (A3-S-PILOT)INCLUDES ELECTRODE   

100-05406  

 PIPE HEX BUSHING, 1/2" x 1/8"-GALVINIZED (BURNER ORFC MOUNT)  

100-05514  

 PVC, 90deg ELBOW - FEMALE 1/2" NPT   

100-06013  

 PVC, COUPLING - FEMALE, 1/2"- NPT   

100-06007  

 PVC, HOSE BARB - MALE, 1/2" - NPT   

100-06014  

 SCREEN INNER 14 GA PRF AL - dia11.250   

210-11250  

 SENSOR, LIQUID LEVER GENTECH INTERNATIONAL   

100-00270  

 SPRAY HEAD BODY & CAP ASS'Y - BRASS (RING OF FIRE)   

100-06002  

 SPRAY HEAD/ADJ. SPOUT ASS'Y - RING OF FIRE   

220-00071  

 SPRAY JETS, BRASS (.900" LONG)   

100-06012  

 SPRAY JETS, BRASS (.900" LONG)   

100-06012  

 SPRAY RING ASS'Y, COPPER - 32.750 o.d. - RING OF FIRE   

100-06003  

 SPRAY RING/JET ASS'Y, ROF   

220-00070  

 STOVE PACK, RING OF FIRE 2002 #294   

225-10294  

 STRAIN RELIEF BUSHING (BLACK)   

100-00141  

 SWIVEL CONNECTOR, FEMALE HOSE-TO 1/2 FEMALE NPT - BRASS   

100-05515  

 THERMODISC - 140deg NC (SNAP-DISC) - NORMALLY CLOSED   

100-00236  

 TUBING CONNECTORS, 1/2" BARBED   

100-06008  

 VALVE, NG - RS (CONVERTIBLE - REGULATED GAS CONTROL)   

100-05512  

 WATER PUMP (COMPLETE), R.O.F. PES-700-PW SERIES   

100-06001  

 WATER PUMP ASS'Y, RING OF FIRE   

228-30039  

 WIRE HRNS, MAIN - R.O.F.   

100-00368  

 

Replacement parts can be obtained from your Ring of Fire retailer.

Summary of Contents for 2003 ROF

































Reviews:

No comments

Brands by name

Popular brands

Load more brands