background image

AC adaptor

7

6

The Choice of Power Supply

.

Slide off the battery cover.

.

Install the batteries by matching 

the correct polarity, as shown.

.

Replace the cover.

1

.Battery powered mode:

    6VDC 4*AA alkaline batteries

2

.AC adaptor powered mode:

   100-240V~, 50-60HZ,400mA

(Can be supplied by AC adaptor model 
UE08WCP-060100SPA only!)

Please unplug the adaptor to depart from 
the using utility power.

Installing and Replacing the Batteries

CAUTION

Remove batteries if the device is not likely to be used for some time.
The old battery is harmful to the environment, so please disposal with other daily trash.
Remove the old battery from the device and follow your local recycling guidelines.

Do not dispose of batteries in fire. Batteries may explode or leak.

CAUTION

Replace the batteries whenever the below happen

The       +       shows

The display dims

The display does not light up

MEASUREMENT

Resting for 5 minutes before 

measuring.

Wait at least 3 minutes between 

measurements. This allows your 

blood circulation to recover.

For a meaningful comparison, 

try to measure under similar 

conditions. For example, take daily 

measurements at approximately 

the same time, on the same arm, 

or as directed by a physician.

Tie the Cuff

1

.Tie the cuff on your upper arm, 

the position the tube off-center 

toward the inner side of arm in 

line with the little finger.

2

.The cuff should be sung but not 

too tight. You should be able to 

insert one finger between the 

cuff and your arm.

3

.Sit comfortably with your tested 

arm resting on a flat surface. 

2~3cm

Note:
The adaptor interface is located on the right side of the monitor. 
Place NO obstacles on the right for easy pull-off adaptor.

In order to get the best effect and protect you monitor,please use the right 

battery and special power adapter which complies with U.S. safety standard.

BEFORE YOU START

4

.Correct Posture for Patients with 

Hypertension, especially for 

Hypertension patient

   - Bare your arm or wear tights only 

when starting measurement.

   - Sit comfortably with legs 

uncrossed, feet flat on the floor, 

back and arm supported.

   The central of the cuff should 

maintain at the same level as the 

right atrium of the heart.

Summary of Contents for LS802-E












Reviews: