background image

Authorized Components

.

Please use the TRANSTEK 

authorized adaptor.

2

.Storage bag.

Adaptor
Type:

UE08WCP-060100SPA

Input:

100~240V

50~60Hz,400mA

Output:

6V      1A

17

16

Contact Information

(Conforms to UL certificate)

AUTHORIZED COMPONENTS

For more information about our products, please visit www.transtek.cn.you can get 

customer service, usual problems and customer download, transtek will serve you 

anytime.

Manufactured by:

GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD

Company:

GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD

Address:

Zone A, 5/F., Investment Building , No. 12, Huizhan East Rd., Torch 

Development District, Zhongshan, Guangdong, 528437, China

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the  

following two conditions: (1) this device may not cause harmful interference, and 

 (2) this device must accept any interference received, including interference that 

may cause undesired operation.

 

Caution: The user is cautioned that changes or modifications not expressly 

approved by the party responsible for compliance could void the user’s authority 

to operate the equipment.

 

NOTE: This equipment has been tested and found to comply with the limits for 

a Class B digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful  

interference in a residential installation. This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular 

installation. 

If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures: 

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver. 

-- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected. 

-- Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an  

uncontrolled environment. 

This transmitter must not be co-located or operating in conjunction with any other 

antenna or transmitter.

FCC Statement

Summary of Contents for LS802-E












Reviews: