2
SGETF10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Part Number
Port One - Copper Port Two - Single Fiber-Optic
SGETF1029-110
RJ-45 1000Base-T
100 m
(328 ft)*
SC, 1000Base-LX, 1310 TX/1550 RX
single mode, 20 km
(12.4 miles)*
SGETF1029-111
RJ-45 1000Base-T
100 m
(328 ft)
*
SC, 1000Base-LX, 1550 TX/1310 RX
single mode, 20 km
(12.4 miles)*
SGETF1029-112
RJ-45 1000Base-T
100 m
(328 ft)*
SC, 1000Base-LX, 1310 TX/1550 RX
single mode, 40 km
(24.8 miles)*
SGETF1029-113
RJ-45 1000Base-T
100 m
(328 ft)*
SC, 1000Base-LX, 1550 TX/1310 RX
single mode, 40 km
(24.8 miles)*
SGETF1029-116
RJ-45 1000Base-T
100 m
(328 ft)*
SC, 1000Base-LX, 1510 TX/1590 RX
single mode, 80 km
(49.7 miles)*
SGETF1029-117
RJ-45 1000Base-T
100 m
(328 ft)*
SC, 1000Base-LX, 1590 TX/1510 RX
single mode, 80 km
(49.7 miles)*
The SGETF1029-11x and the SGETF1029-11x are to be installed in
the same network, where one is the local converter and the other
is the remote converter.
* Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network installation
(TX = transmit, RX = receive).
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
Note:
Third-party Multi-Source Agreement (MSA) compliant Small Form Factor
Pluggables (SFPs) can also be used in the SGETF1040-110.
Sold separately, the following SFP transceiver modules for port two are compatible
with the SGETF1040-110 converter and are available from Transition Networks.
SGETF1040-110 Descriptions
TN-SFP-SX
LC, 1000Base-SX, 850 nm multimode, 220-550 mm
(720-1804 ft)
*
TN-SFP-SXD
LC, 1000Base-SX, 850 nm multimode, 220-550 mm
(720-1804 ft)
*
TN-SFP-LX1
LC, 1000Base-LX, 1310 nm single mode, 10 km
(6.2 miles)
*
TN-SFP-LX3
LC, 1000Base-LX, 1310 nm single mode, 30 km
(18.8 miles)
*
TN-SFP-LX5
LC, 1000Base-LX, 1550 nm single mode, 50 km
(31.2 miles)
*
TN-SFP-LX8
LC, 1000Base-LX, 1550 nm single mode, 80 km
(50.0 miles)
*
TN-SFP-LX12
LC, 1000Base-LX, 1550 nm single mode, 120 km
(74.6miles)
*
Part Number
Port One - Copper Port Two - Single Fiber-Optic
SGETF1040-110
RJ-45 1000Base-T
100 m
(328 ft)*
Open slot for SFP modules
[email protected] -- Click the “Transition Now” link for a live Web chat.
3
Installation
Set the 6-position switch
The 6-position switch is located on
the side of the media
converter.
•
Use a small flat blade
screwdriver to set the
recessed switches.
•
All switches are shown in the
default position, UP.
Note:
Switch positions S2 and S3 work together to configure the media converter
for Pause conditions.
S1
Remote-Fault Detection
up
Disabled
down
Enable
S2 & S3 work in combination
Pause
10 sw position 2 up and 3 down:
Symmetric
01 sw position 2 down and 3 up:
Asymmetric
11 sw positions 2 and 3 up: Pause is OFF
(default position)
00 sw positions 2
and 3 down:
Symmetric and Asymmetric
S4
Transparent Link Pass-Through
up
Enable Link Pass-Through
down
Disable Link Pass-Through
S5
Fiber Auto-Negotiation
up
Disable Fiber Auto-Negotiation for the fiber link
(
default setting)
down
Enable Fiber Auto-Negotiation for the fiber link
S6
Loop Back
up
Disable RX/TX signal loop back
(default setting)
down
Enable RX/TX signal loop back
2. Pause (symmetric)
3. Pause (asymmetric)
4. Transparent Link Pass-Through
5. Auto-Negotiation
1. Remote Fiber Fault Detect
6. Loop Back
