background image

Model 0403

14

1

Ethernet™ Pocket Hub™

1. INTRODUCTION

This guide is intended for the system or network administrator
responsible for installing and monitoring a TRANSITION Networks
0403 Ethernet Pocket Hub. A working knowledge of local area
network (LAN) operations, including familiarity with
communications protocols used on interconnected LANs, is
assumed.

The 0403 Ethernet Pocket Hub

The Model 0403 10BaseT 4-Port Ethernet Hub (E-TBT-HB-0403), is
a low cost Ethernet repeater. Designed to meet IEEE 802.3 10BaseT
standards, the 0403 Pocket Hub is a fully functional repeater in a
compact (4.80" X 2.77" X 0.95”) case. 

0403 Ethernet Pocket Hub Features

automatic link partitioning (jabber function isolates network
failures)

preamble regeneration 

automatic polarity detection and correction

Ethernet™
Pocket Hub™

4            3            2            1

Power

1
2

3
4

E-TBT-0403

Link/Transmit

n

e

t

w

o

r

k

s

T R A N S I T I O N

Mpls, MN 55344

Cable Specifications

Cable Characteristics

The physical characteristics of the 10BaseT cable must meet or exceed
IEEE 802.3 10BaseT specifications. 

10BaseT Cable Specifications
Either shielded or unshielded twisted pair can be used. Level 3 wire or
better is recommended.  

• Gauge. . . . . . . . . . . . . . . . . .  26 to 22 AWG
• Attenuation  . . . . . . . . . . . . .  Less than 11.5 dB @ 5-10 MHz
• Differential Characteristic  . . 85 -110 

Impedance 

@ 10 MHz 

• Maximum Distance  . . . . . . . 100 Meters (330 Feet)

Segment Distance

Media

Maximum

Maximum

Minimum

Maximum

Segment

Number

Segment

Medium Medium

Type

MAU/ 

Length

Propagation

End to End

Segment

(meters)

Velocity

Propagation
Delay/Segment

10Base2

30

185

0.65 c

950 

10BaseT

2

100 

†††

0.59 c

1000

c = 3 x 10

8

meters/second

†††

Maximum segment length depends on the cable characteristics

Summary of Contents for 403











Reviews: