background image

 

Card Reader Limited Warranty 

“Above and beyond” is the standard we set ourselves for customer service at Transcend. 
We consistently position ourselves to be significantly above the industry norm. It’s all part of 
our commitment to Customer Satisfaction. 
 
All Transcend Information, Inc. (Transcend) products are warranted and tested to be free 
from defects in material and workmanship and to conform to the published specifications. 
Should your Transcend Card Reader malfunction during normal use in its recommended 
environment due to improper workmanship or materials within the warranty period, Tran-
scend will repair or replace your product with a comparable product. This warranty is subject 
to the conditions and limitations set forth herein. 
 
Duration of Warranty:    Transcend Card Readers are covered by this warranty for a period 
of two (2) years from the date of purchase. Transcend will inspect the product and make the 
determination as to whether the product is eligible for repair or replacement. The decision 
by Transcend regarding eligibility of the product for repair or replacement will be final and 
binding. Transcend reserves the right to provide a functionally equivalent refurbished re-
placement product. 
 
Limitations:  This warranty does not apply to products that fail due to accident, abuse, 
mishandling, improper installation, alteration, acts of nature, improper usage, or problems 
with electrical power. Transcend Card Reader must be used with devices that conform to 
the recommended industry standards. Transcend will not be liable for damages resulting 
from a third party device that causes the Transcend product to fail. Transcend shall in no 
event be liable for any consequential, indirect, or incidental damages, lost profits, lost 
business investments, lost goodwill, or interference with business relationships as a result 
of lost data. Transcend is also not responsible for damage or failure of any third party 
equipment, even if Transcend has been advised of the possibility. This limitation does not 
apply to the extent that it is illegal or unenforceable under applicable law. 
 
Disclaimer:    The foregoing limited warranty is exclusive, with no other warranties implied or 
statutory, including but not limited to any implied warranty of merchantability or fitness for a 
particular purpose. This warranty is not affected in any part by Transcend’s providing tech-
nical support or advice. 

 

 

Transcend Information, Inc.

 

www.transcendusa.com 

 

 

The Transcend logo is a registered trademark of Transcend Information, Inc. 

*All logos and marks are trademarks of their respective companies. 

 
 

Summary of Contents for TS0MFLRD6E
















Reviews: