manualshive.com logo in svg

Trane Tracer UC400, Installation, Operation And Maintenance Manual

Share
Download
Trane Tracer UC400 Installation, Operation And Maintenance Manual Download Page 2

©2021 Trane

BAS-SVX065E-EN

Introduction

N

No

otte

e:: Specific reference to either UC400 or UC400–B is made throughout this document. All

other content cited in this document about the UC400 is referred to as U

UC

C4

40

00

0 C

Co

on

nttrro

olllle

err.

The UC400/UC400–B is a multi-purpose, programmable (or application-specific) that provides
direct-digital zone temperature control. This controller can operate as a stand-alone device or as
part of a building automation system (BAS). Communication between the controller and a BAS
occurs on an open standard with inter-operable protocols used in Building Automation and
Control Networks (BACnet

®

). Programming is done by means of the Tracer

®

TU service tool.

This guide provides installation and configuration information for the UC400 Controller with
specific operation description for Water Source Heat Pump (WSHP).

Copyright

This document and the information in it are the property of Trane, and may not be used or
reproduced in whole or in part without written permission. Trane reserves the right to revise this
publication at any time, and to make changes to its content without obligation to notify any
person of such revision or change.

Trademarks

All trademarks referenced in this document are the trademarks of their respective owners.

Agency Listings and Compliance

The European Union (EU) Declaration of Conformity is available from your local Trane

®

office.

Revision History

•

Updated table 7 "Output test states" in chapter Typical Applications and Terminations.

•

Added new topic "Constant Torque ECM Fans" in Sequence of Operation chapter.

•

Changed the Dehumidification text to Active Dehumidification.

•

Added new topic "Passive Dehumidification" in Sequence of Operation chapter.

•

Added "Unit Configuration" diagnostics cause and diagnostics in table 18.

•

Running edits.

Summary of Contents for Tracer UC400





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands