Trane Tracer UC400 Installation, Operation And Maintenance Manual Download Page 13

Page: 13 / 60

BAS-SVX065E-EN

Table 5. Factory programmed terminations for Trane GE units (continued)

Inputs/Outputs/Communication

UC400/
UC400–
BController
Terminations

Factory Programmed Assumed Terminations

Binary Outputs (TRIAC)

BO4

Compressor 1 Command

BO5

Compressor 2 Command

BO6

Hot Gas Reheat/Electric Heat

(a)

BO7

Reversing Valve

BO8

Isolation Valve/External Pump

BO9

Outdoor Air Damper

Analog Outputs/Binary Inputs

AO1/BI4

BI- Frost Detect (Coil Ice Protection)

AO2/BI5

BI- Fan Status

Pressure Inputs

PI1

Condensate Overflow

PI2

Unused

Service Button

Test Mode Input

(a)

When Hot Gas Reheat and Electric Heat are present on the same WSHP, Electric Heat will be moved to BO1 on XM32.

The following table lists single compressor control with variable speed fan based on Trane EX/
DX units.

Table 6. Factory programmed terminations for single compressor control for Trane EX/DX units

Inputs/Outputs/Communication

UC400
Controller
Terminations

Factory Programmed Assumed Terminations

Analog Inputs

AI1

Space Temperature Local

AI2

Space Temperature Setpoint Local

AI3

Local Fan Mode Switch

AI4

Discharge Air Temperature Sensor

AI5

Entering Water Temperature Sensor

Universal Inputs

UI1

Relative Humidity Sensor or CO

Sensor

UI2

Leaving Water Temperature

Binary Inputs

BI1

Occupancy Input

BI2

Compressor Protection Status (Monitors High/Low Pressure Cutout
and Freeze Protection)

BI3

Frost Detection

Binary Outputs (Relay)

BO1

Fan Enable

BO2

Water Economizer

BO3

No Connection

Summary of Contents for Tracer UC400





























































Search results

Summary of Contents for Tracer UC400

Reviews:

Related manuals for Tracer UC400

Brands by name

Popular brands

Trane Tracer UC400, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Tracer UC400

Reviews:

Related manuals for Tracer UC400

Brands by name

Popular brands