Trane Thermo King 401586 Maintenance Manual Download Page 29 | Manualshive

Page: 29 / 36

Trane Thermo King 401586 Maintenance Manual Download Page 29

TK 56917-11-MM-EN

29

Diagnostic Procedures using Power Inverter Error Codes

Two types of codes are displayed on the power inverter, Shutdown and Warning.

•

Shutdown error codes will shut the power inverter off.

•

Warning error codes will appear on the display panel to alert of an impending system change. See important note
below.

IIm

mp

po

orrtta

an

ntt:: Warning messages do not immediately effect operation, but could eventually shut down inverter if not

addressed.

Table 4.

Diagnostic Procedures using Power Inverter Error Codes

Error

Code

Condition

Diagnostic Procedures

Shutdown

Inverter has no power, no status
lights

1.

Confirm DC disconnect switch is in the ON position

2.

Confirm power inverter’s power switch is turned ON

3.

Check 150 Amp fuse inside charger enclosure

4.

Check 20 Amp fuse inside charger enclosure

5.

Check 150 Amp fuse near lift gate battery

6.

Check for loose or poor battery connections

7.

Inspect battery cables and wires for abrasions and damage

8.

Use voltmeter to check voltage reading at lift gate battery

E01

Shutdown

Low battery voltage <10.2VDC

Inverter’s display screen will turn off after 30 seconds. After three seconds it will
immediately stop inverting.

1. Check lift gate battery voltage and recharge to greater than 12.6V to clear code.
2. Check for loose or poor lift gate battery connections and tighten as necessary.

E02

Shutdown

High battery voltage >15.75VDC.

Note: The unit will stop inverting.

1. Check voltage regulation of the external charging system of lift gate battery, i.e.,
alternator.

E03

Shutdown

AC output overload

Note: The unit will stop inverting.

1. Verify load is less than 2000 watts.
2. Reduce AC load verify if code clears.
3. Restart inverter.

E04

Shutdown

Over temperature

Note:

NOTE: Inverter will automatically resume operation once inverter’s internal

temperature returns within the normal operating range.

1. Reduce load(s) connected to the GFCI outlet.
2. Check ventilation grille of inverter is not blocked.
3. Move EPJ to cooler location if possible.
4. Turn inverter off for 15 minutes, then restart.

E05

Warning

Low battery voltage detected.
See modes below for details.

Modes:

1. Check lift gate battery voltage and recharge to appropriate voltage based on setting.
2. Check for loose or poor LG battery connections and tighten as necessary.

P01/P02

<12.2 VDC, > 10.2VDC and AC
output will last for one minute.

P03/P04

<12.5 VDC, > 10.2VDC and AC
output will last for three minutes.

E06

Warning

AC output overload warning

1. Reduce load connected to GFCI receptacle.

E07

Warning

Over temperature

1. Reduce load connected to GFCI receptacle.
2. Check ventilation grille of inverter is not blocked.
3. Move EPJ to cooler location if possible.

«
...
27
28
29
30
31
...
»

Summary of Contents for Thermo King 401586





































Reviews:

No comments