background image

©2022

 ACC-SVN240A-EN

Introduction

Read this manual thoroughly before operating or servicing this unit.

Warnings, Cautions, and Notices

Safety advisories appear throughout this manual as required. Your personal safety and the proper 
operation of this machine depend upon the strict observance of these precautions.

Important Environmental Concerns

Scientific research has shown that certain man-made chemicals can affect the earth’s naturally 
occurring stratospheric ozone layer when released to the atmosphere. In particular, several of the 
identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine, Fluorine 
and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon (HCFCs). Not all 
refrigerants containing these compounds have the same potential impact to the environment. 
Trane advocates the responsible handling of all refrigerants-including industry replacements for 
CFCs and HCFCs such as saturated or unsaturated HFCs and HCFCs.

Important Responsible Refrigerant Practices

Trane believes that responsible refrigerant practices are important to the environment, our 
customers, and the air conditioning industry. All technicians who handle refrigerants must be 
certified according to local rules. For the USA, the Federal Clean Air Act (Section 608) sets forth the 
requirements for handling, reclaiming, recovering and recycling of certain refrigerants and the 
equipment that is used in these service procedures. In addition, some states or municipalities may 
have additional requirements that must also be adhered to for responsible management of 
refrigerants. Know the applicable laws and follow them.

The three types of advisories are defined as follows:

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in 
death or serious injury.

CAUTION

s

Indicates a potentially hazardous situation which, if not avoided, could result in 
minor or moderate injury. It could also be used to alert against unsafe practices.

NOTICE

Indicates a situation that could result in equipment or property-damage only 
accidents.

WARNING

Proper Field Wiring and Grounding Required!

Failure to follow code could result in death or serious injury. All field wiring MUST be 
performed by qualified personnel. Improperly installed and grounded field wiring poses FIRE 
and ELECTROCUTION hazards. To avoid these hazards, you MUST follow requirements for 
field wiring installation and grounding as described in NEC and your local/state/national 
electrical codes.

Summary of Contents for Precedent FIADAST003 Series

















Reviews: