background image

ACC-SVN240A-EN

11

Installation

1. Turn the main power disconnect switch 

OFF

.

2. Remove the filter access panel.
3. Remove the rear access panel directly above the horizontal supply duct cover. The sensor tube 

will hang from the fan divider wall with service access to the fan wall from both the rear access 
panel as well as access through the supply duct opening. Refer to 

Figure 14

.

4. Remove the supply air duct cover on the rear side of the unit.
5. Install the sensing tube through the fan wall hole as shown in 

Figure 10

.

Table 1.

Gap analysis chart – B.0 and C.0 cabinet

Heater Type

HZ Gap Low DF Gap Low HZ Gap Med DF Gap Med HZ Gap High DF Gap High

TLSP; GAS heat, B0 Cabinet, 3x3, L2

3/4 inch

3/4 inch

TLSP; GAS heat, B0 Cabinet, 3x4, L2

3/4 inch

3/4 inch

3/4 inch 

3/4 inch 

TLSP; GAS heat, B0 Cabinet, 4x5, L2

3/4 inch

3/4 inch

3/4 inch

Tight

3/4 inch

Tight

TLSP; GAS heat, B0 Cabinet, 6x7, L2

3/4 inch 

Tight

3/4 inch

Tight

TLSP; GAS heat, C0 Cabinet, 4x5, L3

1/8 inch

1/8 inch

1/8 inch

3/4 inch

TLSP; GAS heat, C0 Cabinet, 6x7, L3

1/8 inch 

1/8 inch

Figure 9.

For model: D cabinet (digit 39 = D) horizontal installation

 

Temperature sensing assembly 

with insulation

Secure clamp with 

screws into fan wall

  Secure three tubes 

with screws

Tubing holes face towards front of unit 

(opposite horizontal supply duct)

Tubing holes face vertically 

upwards toward fan

Summary of Contents for Precedent FIADAST003 Series

















Reviews: