background image

CLCH-SVX013B-EN

Pre-Installation

Receiving and Handling

Inspection

Upon delivery, thoroughly inspect all components for any 
shipping damage that may have occurred, and confirm 
that the shipment is complete. See 

“Receiving Checklist” 

 

section for detailed instructions.

Note:

Delivery cannot be refused. All units are shipped 
F.O.B. factory. Trane is not responsible for shipping 
damage.

Packaging/Shipping

Performance air handlers ship as a complete unit or in 
individual sections to be field assembled. Indoor air 
handler sections are stretch-wrapped or shrink-wrapped 
before shipping. All factory shipping protection should be 
removed upon delivery. This wrapping is for transit 
protection only.

Indoor Performance air handlers ship in subassemblies if 
the total length of the units exceeds 98 inches or if the total 
weight exceeds factory limits.

Outdoor Performance air handler sections are not 
wrapped, but openings are covered to comply with LEED 
EQ Credit 5.

Smaller components and hardware may be shipped 
separately, or shipped inside the unit. This hardware is 
typically packaged in a clear plastic envelope or cardboard 
box, and can be found inside the fan, mixing box, or access 
section.

Identification

Each air handler section includes a nameplate identifying 
the section type and functional components, customer 
tagging information, unit serial number, unit order 
number, the build-section position for installation, and the 
unit model number. See 

“Nameplate,” p. 6.

Handling

Air handlers have an integral base frame designed with 
the necessary number of lift points for safe installation. 
See 

“Lifting and Rigging,” p. 14

Receiving Checklist

Complete the following checklist immediately after 
receiving shipment to detect possible shipping damage.

Check to ensure that the shipment is complete. Small 
components may ship inside the unit or ship 
separately. Check the parts list to ensure all materials 
are present. If any component is missing, contact your 
local Trane sales office.

Check all units, components, connections, and piping. 
Check fan wheel for free rotation by spinning 
manually. Check all doors, latches and hinges. Inspect 
interior of each unit or section. Inspect coils for 
damage to fin surface and coil connections. Check for 
rattles, bent corners, or other visible indications of 
shipping damage. Tighten loose connections.

If a unit is damaged, make specific notations 
concerning the damage on the freight bill. Do not 
refuse delivery.

Notify the carrier’s terminal of the damage 
immediately by phone and mail. Request an 
immediate joint inspection of the damage by the 
carrier and consignee.

Notify your Trane sales representative of the damage 
and arrange for repair. Do not attempt to repair the unit 
without consulting the Trane representative.

Inspect the unit for concealed damage as soon as 
possible after delivery. Report concealed damage to 
the freight line. It is the receiver’s responsibility to 
provide reasonable evidence that concealed damage 
did not occur after delivery. Take photos of damaged 
material if possible.

Note:

Concealed damage must be reported within 15 
days of receipt.

Jobsite Storage

Indoor air handlers and field-installed accessories must be 
protected from the elements. A controlled indoor 
environment is recommended for proper storage. 

Note:

All factory shipping protection should be removed, 
This wrapping is for transit protection only.

The unit controller and all other electrical/electronic 
components should be stored in conditions of -20°F to 
120°F and 5 to 95 percent relative humidity, non-
condensing. Electrical components are not moisture-
tolerant. 

Outdoor units require no special protection for storage 
prior to installation. 

Outdoor Storage

NOTICE

Corrosion!

Use only canvas tarps to cover air handlers. Plastic 
tarps can cause condensation to form in and on the 
equipment, which could result in corrosion damage or 
wet storage stains. 

Outdoor storage is 

not

 recommended for units that will be 

installed indoors. However, when outdoor storage is 

Summary of Contents for Performance Climate Changer PSCA



















































































Reviews: