Trane Odyssey TWA0604DA, Installation, Operation And Maintenance Manual

Page: 25 / 40

SSP-SVX001B-EN 25
Unit Power Supply
The installer must provide line voltage circuit(s) to the
unit main power terminals as shown by the unit wiring
diagrams. Adhesive backed diagrams are affixed inside
the control box cover panel. Wiring diagrams are also
available through e-Library or by contacting a local
sales office. Power supply must include a disconnect
switch in a location convenient to the unit. Ground the
unit according to local codes and provide flexible
conduit if codes require and/or if vibration transmission
may cause noise problems.
IIm mp po orrtta an ntt:: All wiring must comply with applicable
local and national (NEC) codes. Type and
location of disconnect switches must
comply with all applicable codes.
W WA AR RN NIIN NG G
P Prro op pe err F Fiie elld d W Wiirriin ng g a an nd d G Grro ou un nd diin ng g
R Re eq qu uiirre ed d!!
F Fa aiillu urre e tto o ffo ollllo ow w cco od de e cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
A Allll ffiie elld d w wiirriin ng g M MU US ST T b be e p pe errffo orrm me ed d b by y q qu ua alliiffiie ed d
p pe errsso on nn ne ell.. IIm mp prro op pe errlly y iin nsstta alllle ed d a an nd d g grro ou un nd de ed d
ffiie elld d w wiirriin ng g p po osse ess F FIIR RE E a an nd d E EL LE EC CT TR RO OC CU UT TIIO ON N
h ha azza arrd dss.. T To o a av vo oiid d tth he esse e h ha azza arrd dss,, y yo ou u M MU US ST T ffo ollllo ow w
rre eq qu uiirre em me en nttss ffo orr ffiie elld d w wiirriin ng g iin nsstta alllla attiio on n a an nd d
g grro ou un nd diin ng g a ass d de essccrriib be ed d iin n N NE EC C a an nd d y yo ou urr llo occa all//
sstta atte e//n na attiio on na all e elle eccttrriicca all cco od de ess..
N NO OT TIIC CE E
U Usse e C Co op pp pe err C Co on nd du ucctto orrss O On nlly y!!
F Fa aiillu urre e tto o u usse e cco op pp pe err cco on nd du ucctto orrss cco ou ulld d rre essu ulltt iin n
e eq qu uiip pm me en ntt d da am ma ag ge e a ass tth he e e eq qu uiip pm me en ntt w wa ass n no ott
d de essiig gn ne ed d o orr q qu ua alliiffiie ed d tto o a acccce ep ptt o otth he err tty yp pe ess o off
cco on nd du ucctto orrss..
Low Voltage Wiring
Mount the indoor thermostat, zone sensor, or
programmable zone sensor in accordance with the
corresponding thermostat installation instructions.
Install color-coded, weather-proof, multi-wire cable
according to the field wiring instructions (see
“Field
Wiring,” p. 26 ).
N No otte e:: Refer to thermostat or zone sensor wire
installation guide for proper wire gauge.
Symbio ™ ™ Controls
Wiring shown with dashed lines is to be furnished and
installed by the customer. All customer supplied wiring
must be copper only and must conform to NEC and
local electrical codes. Codes may require line of sight
between disconnect switch and unit.
Figure 14. Symbio ™ ™ jobsite connections
Zone Sensor
See Note 2
T’stat
See Note 2
Air Handler
Disconnect Switch
(By Others)
Disconnect Switch
(By Others)
See Note 1
Electric
Heat Accessory
Disconnect Switch
(By Others)
See Note 1
B
A
B
D
E C
P Po ow we err W Wiirre ess
A. 3 wires, line voltage for 3 phase, (2 wires for single
phase) 1 grounding wire
B. 3 wires, line voltage for 3 phase, (2 wires for single
phase) 1 grounding wire
C Co on nttrro oll W Wiirre ess
C. Heat Pump thermostat: 6 to 9 wires depending on
T’stat options and stages of cooling and heating
D. Wiring between indoor and outdoor unit: 5 to 11
wires depending on unit control options*
E. Zone Sensor: 4 to 7 wires depending on zone sensor
model*
*Communication signal wires require twisted pairs.
Refer to unit schematics for identification of twisted
pairs.
N No otte ess::
1. When electric heater accessory is used,
single point power entry or dual point power
entry is field optional. Single point power
entry option is through electric heater only.
2. ***Choose only one of the following;
Thermostat, Mechanical Zone Sensor,
Programmable Zone Sensor Panel or BAS
Zone Sensor.
IIm mp po orrtta an ntt:: For the EDC switch to be functional and
thereby facilitate reliable unit operation,
make the EDC connections from the indoor
to the outdoor control boxes.
IIn nsstta alllla attiio on n