background image

16 

AMS-SVX02A-EN

Unit Installation

Refrigerant pipe connection

As shown in fig. 10, use wrench and torque wrench simultaneously for removing or 

• 

installing pipes.

Apply refrigerating engine oil on the tapered nut inside and outside, and then tighten it 

• 

after 3-4 turns manually.

Tightening torque see table. 1 (over tighten may damage the nut and cause leakage)

• 

As shown in fig. 10, check the connecting pipe for air leakage and take heat insulation 

• 

measures.

Wrap joints of air pipe and air collector pipe insulating sleeve with the sponge.

• 

Apply refrigerating 
engine oil

Torque wrench

Wrench

Pipe joint

Liquid inlet pipe

Air collector pipe

Cable tie (x4)

Air collector pipe 
insulating sleeve (accessory) 
(For air pipe)

Liquid inlet pipe 
insulating sleeve (accessory) 
(For liquid pipe)

Tapered nut

Sponge (accessory)
(Wrap pipe joints with seal)

Figure 10. 

Torque for tighten the nut

Table 1. 

Diameter

Wall thickness 

(mm)

Tightening torque

Ø6.35mm

≥ 0.5

15-30 (N•m)

Ø9.52mm

≥ 0.71

30-40 (N•m)

Ø12.7mm

≥ 1

45-50 (N•m)

Ø15.9mm

≥ 1

60-65 (N•m)

Ø19.05mm

≥ 1

70-75 (N•m)

Summary of Contents for MWC518





























Reviews: