manualshive.com logo in svg

Trane CeilAir CW, Installation, Operation And Maintenance Manual, Page: 31 / 52

Share
Download
Trane CeilAir CW Installation, Operation And Maintenance Manual Download Page 31

Table 8.

Refrigerant pressure/temperature settings 

Refrigerant Pressure/Temperature Settings

Normal

Min.

Max.

Sub-cooling°F

10

5

20

Superheat°F

15

10

20

Design Condensing Temp. 

@ 95°F Ambient

125

105

140

Suction Pressure (psig)- 

R407C

70

55

85

Fan Cycling Control- Fan On 

(psig)- R407C

320

240

340

Fan Speed Control (psig)- 

R407C

320

-

-

Flooded HP Control Valve 

(psig)- R407C

205

Installation

AH-SVX008C-EN

31 

Saturated Refrigerant Pressure Tables

The following table shows the refrigerant pressures are 
provided for reference for R407C refrigerant.

Table 9.

Refrigerant vapor tables 

R407C Refrigerant

Temp.

(°F)

Pressure 

(psig)

Saturated Evaporating Temperature

20

37.9

Dew Point

Saturated

Vapor

22

40.1

24

42.3

26

44.7

28

47.1

30

49.6

32

52.1

34

54.8

36

57.5

38

60.3

40

63.2

42

66.1

44

69.2

46

72.3

48

75.5

50

78.8

Saturated Evaporating Temperature

Bubble Point

 

Saturated

Vapor

95

209

100

225

105

242

110

260

115

279

120

298

125

319

130

341

135

363

140

387

Summary of Contents for CeilAir CW





















































Reviews:

No comments