manualshive.com logo in svg

Trane CeilAir CW, Installation, Operation And Maintenance Manual, Page: 24 / 52

Share
Download
Trane CeilAir CW Installation, Operation And Maintenance Manual Download Page 24

Figure 19.

Interconnection field wiring remote condenser

SEE NOTE 3

REMOTE TEMPERATURE 

SENSOR (OPTIONAL)

REMOTE TEMPERATURE/ 

HUMIDITY SENSOR 

(OPTIONAL)

SEE NOTE 3

3 CONDUCTOR

SHIELDED CABLE

E² 

CONTROLLER DISPLAY

E² DISPLAY PLUGS DIRECTLY INTO THE 

CONTROLLER INSIDE THE ELECTRIC BOX

6 CNDCT. PHONE TYPE
NON-SHIELDED CABLE

24 VAC (OPTIONAL)

E²

 CONTROL CONFIGURATION (OPTIONAL)

THERMOSTAT 

CONTROL 

CONFIGURATION (OPTIONAL)

NOTES:
1. DASHED WIRES (                       ) NOT APPLICABLE FOR SINGLE-STAGE UNITS

2. PHANTOM WIRES (                     ) NOT APPLICABLE FOR SINGLE PHASE POWER SUPPLIES
3. OPTIONAL REMOTE MOUNTED DEVICE WIRES DIRECTLY TO A/C UNIT TERMINAL BLOCK
4. CONDUCTOR COUNTS IN FIGURE ARE NOTIONAL. SEE UNIT ELECTRICAL DRAWING FOR
    ACTUAL NUMBER AND TERMINAL POINTS OF CONDUCTORS

Figure 20.

Interconnection field wiring remote condensing unit 

SEE NOTE 3

REMOTE CONDENSING UNIT

REMOTE TEMPERATURE/ 

HUMIDITY SENSOR 

(OPTIONAL)

SEE NOTE 3

3 CONDUCTOR

SHIELDED CABLE

E²

 

 CONTROLLER DISPLAY

E² DISPLAY PLUGS DIRECTLY INTO THE 

CONTROLLER INSIDE THE ELECTRIC BOX

6 CNDCT. PHONE TYPE
NON-SHIELDED CABLE

THERMOSTAT 

CONTROL 

CONFIGURATION (W/ OPTIONS)

E²

 CONTROL CONFIGURATION (OPTIONAL)

NOTES:
1. DASHED WIRES (                       ) NOT APPLICABLE FOR SINGLE-STAGE UNITS

2. PHANTOM WIRES (                     ) NOT APPLICABLE FOR SINGLE PHASE POWER SUPPLIES
3. OPTIONAL REMOTE MOUNTED DEVICE WIRES DIRECTLY TO A/C UNIT TERMINAL BLOCK
4. CONDUCTOR COUNTS IN FIGURE ARE NOTIONAL. SEE UNIT ELECTRICAL DRAWING FOR
    ACTUAL NUMBER AND TERMINAL POINTS OF CONDUCTORS

Installation

24

 AH-SVX008C-EN

Summary of Contents for CeilAir CW





















































Reviews:

No comments