Trane Agility HDWA, Installation, Operation And Maintenance Manual

Page: 70 / 76

70 HDWA-SVX001D-EN
Appendix B: Agility ™ ™ Chiller Installation Completion
and Request for Trane Service
IIm mp po orrtta an ntt:: A copy of this completed form must be
submitted to the Trane Service Agency that
will be responsible for the start-up of the
chiller. Start-up will NOT proceed unless
applicable items listed in this form have
been satisfactorily completed.
TO:
TRANE SERVICE OFFICE:
S.O. NUMBER:
SERIAL NUMBERS:
JOB/PROJECT NAME:
ADDRESS:
The following items
are being installed
and will be completed by:
IIm mp po orrtta an ntt:: Start-up must be performed by Trane or an
agent of Trane specifically authorized to
perform start-up and warranty of Trane
®
products. Contractor shall provide Trane
(or an agent of Trane specifically
authorized to perform start-up) with notice
of the scheduled start-up at least two weeks
prior to the scheduled start-up. E
Eq qu uiip pm me en ntt
n no ott sstta arrtte ed d b by y T Trra an ne e iiss n no ott w wa arrrra an ntte ed d b by y
T Trra an ne e..
Check box if the task is complete or if the answer is
“yes”.
1. A Ag giilliitty y ™ ™ C Ch hiilllle err
☐ Installation meets foundation requirements.
☐ In place and piped.
☐ Isolation pads installed.
N No otte e:: Do not insulate the Agility ™ chiller or
adjacent piping prior to the chiller
commissioning by Trane service personnel.
The contractor is responsible for any foreign
material left in the unit.
2. P Piip piin ng g
Chilled water piping connected to:
☐ Evaporator
☐ Air handling units
☐ Pumps
☐ Flow switch or flow proving device installed (if
not factory-provided)
Condenser piping connected to:
☐ Condenser
☐
Pumps
☐ Flow switch or flow proving device installed (if
not factory-provided)
☐
Cooling tower
Additional piping:
☐ Make-up water connected to cooling tower
☐ Water supply connected to filling system
☐ Does unit have freeze inhibitor? If unit has
freeze inhibitor:
☐ Verify type and concentration correct per
unit submittal
☐ Calculate and record freeze point of the
solution: ___________ (specify °F or °C)
☐ Systems filled
☐ Pumps run, air bled from system
☐ Strainers installed in entering water piping
(evaporator and condenser) and cleaned
☐ Relief valve ventilation piping installed (as
applicable)
3. F Fllo ow w b ba alla an ncciin ng g v va allv ve ess iin nsstta alllle ed d
☐ Leaving chilled water
☐ Leaving condenser water
☐ Proper porting to measure flow and balance
4. G Ga au ug ge ess,, tth he errm mo om me ette errss,, a an nd d a aiirr v ve en nttss
☐ Installed on both sides of evaporator
☐ Installed on both sides of condenser
5. W Wiirriin ng g
☐ Wire size per submittal and NEC 310-16
☐
Full power available
☐ External interlocks (flow switch, pumps
auxiliary, etc.)
☐ Chilled water pump (connected and tested)
☐ Condenser water pump (connected and tested)
☐ Cooling tower fan rotation checked
☐ 115 Vac power available for service tools (as
required)
☐ All controls installed and connected
☐ If unit was disassembled for installation , all
interconnecting wiring reinstalled
☐ For CVHS and CVHM chillers, indicate type of
power distribution grounding:
☐ Solidly Grounded (Center Ground Wye)
-or-
☐ Non-Solidly Grounded (Any Delta, High