background image

 

     

  9 

Duty Cycle 

The Air Compressor should not be operated on more than a 60% duty cycle. This means an air compressor that 

pumps air for over 6 minutes in one ten minute period is considered misuse. This could mean that the air compressor 

is undersized for the required air demand. The maximum compressor pump time per hour is 30 minutes. 

 

“Caution”    - Always be aware of the duty cycle for your air compressor. Failure to operate the air 

compressor properly could result in overheating and motor seizure. There could also be risk of fire hazard 

due to overheating. Be sure to use a compressor capable of handling the air demand. 

 

 

 

Operating the unit 

To start the air compressor: 

1. 

Make sure the compressor switch is in the 

OFF 

position (knob with red cap above pressure gauges shown in 

Figure 2 

pressed down) before connecting the power supply.   

 

 

 

Figure 2. 

ON/OFF button. 

Check the pressure gauge to see that the tank pressure climbs to approximately 

( 8 BAR for 

MCFRC230/231/232/233/234/238/239/227/228/229 and PE50300; 12 BAR for PE75300, PE 100300, PE100500 

and PE150500)

, then automatically turns off. 

Note

If the compressor does not automatically switch off, flip the ON/OFF switch to OFF before pressure gets too 

high. See the Pressure Regulator sub-section. 

 

 

Summary of Contents for MCFRC227






















Reviews: