TPS WP-80D Manual Download Page 13

Page: 13 / 45

Page 13

4. pH Calibration

A “

∗

” in place of the decimal point indicates that the pH readout is not

calibrated, or a past calibration has failed. The “

∗

” will be removed once

a full two-point pH calibration has been successfully performed.

4.1 Calibration Procedure

1. Plug the pH sensor into the

Channel 1

Channel 2

socket and the

temperature sensor into the

Temperature

socket.

2. Switch the meter on.

3. Ensure that you are using buffers which have been selected for

automatic buffer recognition. See section 15 for a detailed
explanation.

4. Select pH Mode.

Either (

→

F3:Mode

→

F1:Chan1

→

F1:pH

)

(

→

F3:Mode

→

F2:Chan2

→

F1:pH

)

5. Ensure that temperature has already been calibrated, or manually set

(see sections 7.1 and 7.4). NOTE: If the decimal point in the
temperature reading is shown by a "

∗

", then the temperature readout

is not calibrated.

6. Remove the wetting cap from the pH sensor.

7. Rinse the pH and Temperature sensors in distilled water and blot

them dry.

8. Place both electrodes into a small sample of pH7.00 (or pH6.86)

buffer, so that the bulb and reference junction are both covered, as
per the diagram over the page.

DO NOT

place the electrodes directly into the buffer bottle.

9. Select pH Calibration.

Either

→

F1:Cal.

→

F1:pH1

→

F1:Cal.

→

F2:pH2

Summary of Contents for WP-80D














































Search results

Summary of Contents for WP-80D

Reviews:

TPS WP-80D, Manual, Page: 13 / 45

Search results

Summary of Contents for WP-80D

Reviews: