background image

 

Section 5 – Warranty

 

 

15

Section 5. –  Warranty 

TPS  Pty.  Ltd.  guarantees  all  instruments  and  sensors  to  be  free  from  defects  in  material  and 
workmanship when subjected to normal use and service. This guarantee is expressly limited to the 
servicing  and/or  adjustment  of  an  instrument  returned  to  the  Factory,  or  Authorised  Service 
Station, freight prepaid, within twelve (12) months from the date of delivery, and to the repairing, 
replacing, or adjusting of parts which upon inspection are found to be defective. Warranty period 
on sensors is three (3) months. 

There  are  no  express  or  implied  warranties  which  extend  beyond  the  face  hereof,  and  TPS  Pty. 
Ltd. is not liable for any incidental or consequential damages arising from the use or misuse of this 
equipment, or from interpretation of information derived from the equipment. 

Shipping damage is not covered by this warranty. 

PLEASE NOTE 

A guarantee card is packed with the instrument or sensor. This card must be completed at the time 
of purchase and the registration section returned to TPS Pty. Ltd. within 7 days. No claims will be 
recognised without the original guarantee card or other proof of purchase. This warranty becomes 
invalid  if modifications  or  repairs  are  attempted by  unauthorised  persons, or the  serial number  is 
missing. 

PROCEDURE FOR SERVICE 

If  you  feel  that  this  equipment  is  in  need  of  repair,  please  re-read  the  manual.  Sometimes, 
instruments are received for "repair" in perfect working order. This can occur where the sensor(s) 
simply requires cleaning or replacement or some other field serviceable event. 

TPS Pty. Ltd. has a fine reputation for prompt and efficient service. In just a few days, our factory 
service engineers and technicians will examine and repair your equipment to your full satisfaction. 

To obtain this service, please follow this procedure… 

Return  the  instrument  AND  ALL  SENSORS  to  TPS  freight  pre-paid  and  insured  in  its  original 
packing  or  suitable  equivalent.  INSIST  on  a  proof  of  delivery  receipt  from  the  carrier  for  your 
protection in the case of shipping claims for transit loss or damage. It is your responsibility as the 
sender to ensure that TPS receives the unit. 

Please check that the following is enclosed with your equipment: 

 

Your Name and daytime phone number. 

 

Your return street address. 

 

A description of the fault. (Please be SPECIFIC.) 
(Note: "Please Repair"  does NOT describe a fault.) 

Your equipment will be repaired and returned to you by air express where possible. 

For out-of-warranty units, a repair cost will be calculated from parts and labour costs. If payment is 
not  received  for  the  additional  charges  within  30  days,  or  if  you  decline  to  have  the  equipment 
repaired,  the  complete  unit  will  be  returned  to  you  freight  paid,  not  repaired.  For  full-account 
customers, the repair charges will be debited to your account. 

Summary of Contents for easyFLOW-VS


















Reviews: