TPS 113140 Manual Download Page 6 | Manualshive

Page: 6 / 33

background image

Page 6

1.2 Unpacking Information

Before using your new

mini

CHEM

-DO

2

, please check that the following

accessories have been included:

Part No

1.

mini

CHEM

-DO

2

Process Monitor ......................... 113140

2.

mini

CHEM

-DO

2

Handbook .................................. 130050

Options that may have been ordered with your miniCHEM-DO

2

:

TPS Dissolved Oxygen Sensor (submersible to 3 metres max)…

1.  ED1M Dissolved Oxygen sensor (no cable) ............ 123440
2.  5m cable for ED1M ............................................... 123236
3.  Extended cable (per metre) ..................................... 130040

YSI Dissolved Oxygen Sensor and separate cable…

1.  EDYSI Dissolved Oxygen sensor (no cable) ........... 123204
2.  5m cable for EDYSI .............................................. 123210
3.  Extended cable (per metre) ..................................... 130040

Instrument options…

1. Relay control output............................................... 130342
2. 4-20mA loop-powered, remote LCD....................... 130080

Spares…

1.  Membrane Kit for ED1M....................................... 123301
2.  Membrane Kit for EDYSI...................................... 123300
3.  Sodium Sulphite for Zero calibration...................... 123302

«
...
4
5
6
7
8
...
»

Summary of Contents for 113140


































Reviews:

No comments

Related manuals for 113140

Brand: iHealth Pages: 16

Brand: OBH Nordica Pages: 60

Brand: Pixio Pages: 12

Brand: Dot-x Pages: 12

Brand: Rockwell Automation Pages: 64

Brand: MultiTouch Pages: 16

PRTD-090T-5A-N4F

Brand: Icop Pages: 32

Brand: Feelworld Pages: 8

My Tensio BW-BA1

Brand: bewell connect Pages: 34

Brand: Power Acoustik Pages: 11

Brand: Samsung Pages: 43

Brand: Samsung Pages: 51

Brand: Samsung Pages: 57

Brand: Samsung Pages: 116

Brand: Samsung Pages: 137

Brand: Samsung Pages: 37

Brand: INNOLIVING Pages: 52

Brand: Acer Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands