TP-Link HC220 User Manual Download | Manualshive

Page: 84 / 110

background image

80

Chapter 13

Manage Your APAP

(path) your router has passed to reach the tested host, and measure transit delays of

packets across an Internet
Protocol network.

Nslookup:

Enter the Domain name, you can check whether DNS is resolving domain

name normally and the diagnostic result will be display.

Note:

Click

Advanced

, you can modify the ping count, ping packet size or the Traceroute Max TTL. It’s recommended to keep

the default value.

13. 4. Update the Firmware

TP-Link is dedicated to improving product features, giving you a better network
experience.
We will inform you through the web management page if there’s any update firmware
available for your AP. The latest firmware can also be downloaded from the

Support

page of our website

www.tp-link.com

for free.

Note:

1. Make sure that you have a stable connection between the AP and your computer. It is NOT recommended to upgrade

the firmware wirelessly.

2. Back up your AP configuration before upgrading the firmware.
3. DO NOT turn off the AP during the firmware upgrade.

You can follow the steps below to manually update the firmware.
1. Download the latest firmware file for the AP from our website

www.tp-link.com

.

2. Visit

http://tplinkwifi.net

, and log in with the password you set for the AP.

3. Go to

Advanced

>

System Tools

>

Firmware Upgrade

.

4. Focus on the

Device Information

section. Make sure the downloaded firmware file

matches with the

Hardware Version

.

5. Focus on the

Local Upgrade

section. Click

Browse

to locate the downloaded new

firmware file, and click

Upgrade

.

Note:

The upgrading will also take effect on the synced online agents. We recommend that you keep the AP and its agents in
the same firmware version. Please do not turn off the AP and its agents during the firmware upgrading process.

6. Wait a few minutes for the upgrading and rebooting.

13. 5. Back Up and Restore Configuration Settings

The configuration settings are stored as a configuration file in the AP. You can back up
the configuration file to your computer for future use and restore the AP to a previous
settings from the backup file when needed. Moreover, if needed you can erase the
current settings and reset the AP to its default factory settings.

«
...
82
83
84
85
86
...
»

Summary of Contents for HC220















































































































Reviews:

No comments

Related manuals for HC220

Brand: Parker Pages: 344

Brand: Cabletron Systems Pages: 21

Brand: Patton electronics Pages: 8

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

Brand: WAGO Pages: 2

Brand: Zonet Pages: 8

Brand: FOR-A Pages: 72

Brand: National Instruments Pages: 130

Brand: Ubiquiti Pages: 13

VIGI NVR1004H-4P

Brand: TP-Link Pages: 2

Brand: AIC Pages: 101

ADSL Ethernet & USB Combo Router Lynx L-510

Brand: Starbridge Networks Pages: 59

Brand: JAKA Pages: 37

Brand: Socket Pages: 28

Brand: Ubiquiti Pages: 20

Brand: Milesight Pages: 15

TE100S8P - Fast Ethernet Switch

Brand: TRENDnet Pages: 11

Brand: Planet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands