background image

1

1. THE SUMMARY

The idea behind the unit is to provide a localized supply of cool air.
The unit will greatly enhance your personal comfort whether at a work station or even in your favorite chair.
Four (4) casters enable you to move the unit easily from room to room. It cools and dries the air at the same
time so that you can stay comfortable even when it's humid or rainy outside. Also your furnishings and fabrics
are kept in good condition when it's used as dehumidifier.
Conventional air conditioners use large quantities of energy to cool an entire room, including walls and furni-
ture. This unit creates a zone of cool and dry air only where it is needed. It does not waste energy cooling the
surroundings.
It's easy to operate. The built-in timer allows from 1 to 12 hours of operation, which will automatically turn the
unit on and off. This is especially convenient at bedtime.
Venting is not required. However, if the unit is to be used exclusively in one space, the cooling efficiency will be
enhanced by using the venting kit accessory, which is included with the unit.

2. OPERATIONAL FEATURES

1. COOLING OPERATION:

Normally, cool air is directed out the front louvers by the circulation fan which has three (3) stages of fan
speed.

2. AUTOMATIC OPERATION:

The unit will select its mode and fan speed automatically base on the environment temperature.

3. THERMO CONTROL

The compressor will automatically shift to ON or OFF to maintain the desired temperature.

4. TIMER OPERATION:

The unit will turn on and off after the designated period of time (1, 2, 3, ...12 hours).

5. AUTOMATIC SHUT-OFF MECHANISM WHEN THE DRAIN TANK IS FULL:

When the drain tank is full, the unit will be automatically shut off. It is always required to press the power
button twice to resume operation after the condensed water is removed from the tank.

6. TRIPLE AIR FILTERS:

The pre-filter protects the unit from dust, the HAF air filter (Type B is an option) cleans circulation air and the
charcoal filter eliminates unpleasant odor.

  TAD-T32G  (Service  Manual)    07.1.17  3:03  PM    ページ 1

Summary of Contents for TAD-T32G




















Reviews: