11
3) Setting of a day of the week
“dAy” sign is shown on the display and all of days of the week will blink.
Press the “
▲
MIN.” button or the “
▼
HOUR” button to set a day of the week. A day of the week will blink. (Initial
setting is “SUN”.) The other days of the week will go off. Select a day of the week by using the “
▲
MIN.” or the
“
▼
HOUR” button. When pressing the “
▲
MIN.” button, the sign will change as follows.
“SUN”
➞
“MON”
➞
“TUE”
➞
“WED”
➞
“THU”
➞
“FRI”
➞
“SAT”
When pressing the “
▲
MIN.” button at the position of “SAT”, you can hear a beep sound and “SAT” is not
changed any more. When pressing the “
▼
HOUR” button, the sign will change as follows.
“SAT”
➞
“FRI”
➞
“THU”
➞
“WED”
➞
“TUE”
➞
“MON”
➞
“SUN”
When pressing the “
▼
HOUR” button at the position of “SUN”, you can hear a beep sound and “SUN” is not
changed any more.
Press the “SET” button to complete the setting of the days of the week. The current time and a day of the week
will show on the display.
Note: If the ON/OFF switch is pressed during setting of the current time and a day of the week after setting the
time and a day of the week, the set mode of the current time will terminate and the operation will start. If a
day of the week is set, the time is fixed. If a day of the week is not set, the contents of the setting are
deleted.
OPERATION
MANUAL OPERATION
Operation of the heater is under the direct control of the user. Heat output will, however, be automatically
adjusted in accordance with the room temperature registered by the temperature sensor.
1. Turn Heater ON
A. Press ON/OFF button to “ON” position. The current room temperature and the set temperature will be
shown on the Display. If the room temperature is below the set temperature then ON lamp will start to flash
and then blower motor and ignition will start. This lamp will continue to flash during the preheating time.
B. Pre -heating depends on the room temperature. After approx. 1.5 – 4 minutes ignition will take place.
After ignition, ON lamp will change flashing to continuous. Circulation fan will turn on after approx. 2 minutes.
Note: Room temperature: below 33˚F
Approx. 4 minutes
33˚F - 59˚F
" 2 minutes
over 59˚F
" 1.5 minutes
2. Adjusting Room Temperature
A. Press “HOUR” or “MIN.” button. ˚F or ˚C symbol will start to flash.
Note: “HOUR” or “MIN.” button will change the temperature in increment of 2˚F (1˚C).
B. Press “MIN.” for up and “HOUR” for down. Room temperature can be set from 50˚F (10˚C) to 90˚F (32˚C).
(Initial setting : 56˚F (13˚C))
C. When room temperature reaches the selected setting, heater will automatically shift to “MED” or “LOW”
burning mode to maintain the desired temperature.
When room temperature exceeds the selected setting by approx. 4˚F (2˚C), the heater will automatically shut
off. As room temperature drops, the heater will automatically re-start to maintain the desired temperature.
POWER SAVER OPERATION
The Power Saver mode reduces the frequency of ignition actions, to save electric consumption.
Press the POWER SAVER button “ON” while in operation to start the operation of the “POWER SAVER”.
“POWER SAVER” sign will be shown on the display.
When the room temperature exceeds the selected setting by approximately 12˚F (6˚C), the heater will
automatically shut off. As the room temperature becomes lower than the selected setting, the heater will
automatically re-start to maintain the desired temperature.
Approx. +2˚F
SET
TEMP.
High
Medium
Low
Off
Re-lgnition
Approx. +4˚F
Approx. +12˚F
Approx. +2˚F
SET
TEMP.
High
Medium
Low
Off
Re-lgnition
Summary of Contents for Laser 531
Page 35: ......