background image

VSS3    

11

3.3. Ignition Controlled door lock

This option is disabled as default. To enable it, please contact your authorised retailer.
When you turn the ignition key ON, the system will lock the doors.
The alarm system will unlock all doors when the ignition is turned OFF.

3.4. Passive arming

This option is disabled as default and can be enabled (at your authorised retailer).

Passive arming mode arms the alarm system automatically without the car being locked. It protects 
your car in case you forget to lock it. 

When this option is activated, it will arm the alarm system after following these steps:
1.   The engine is stopped, and the key is removed from the ignition.
2.   A door has been opened and all doors have been closed again.

If any door is opened when the alarm system is in passive arming, the siren will sound unless the 
unlock button on the remote control is pressed.

Note: 
–  During passive mode, volumetric sensors are activated.
–  If you lock the car by remote control, the alarm system shifts to normal arming mode.

Remark:
–  The system does 

NOT

 lock any doors, only arms the alarm system.

Summary of Contents for VSS3-Hilux



















Reviews: