background image

10

    VSS3

3. Features

As well as the alarm function, some extra features are available which can be activated/deactivated. 
To activate or deactivate any of them, please contact your authorised retailer.

3.1. Door ajar warning 

This option is enabled as default.
If any door or the boot is opened when the lock button is pressed, the buzzer will sound for 
10 times. The buzzer will stop sounding when all doors are closed, or if the remote control unlock 
button is pushed.
If the bonnet is opened when the lock button is pressed, the buzzer will sound 3 times with 
3 beeps.

Note: 
–  The alarm system will arm, even if a door is open.

3.2. Alarm override 

This function is used if the user loses the remote, or the remote battery is flat.

To arm / disarm the system 

1

Press the button on the LED push button the number of times that corresponds to the first 
digit of the PIN Code, with a maximum 1.5 second delay between one press and the next. 
If the LED is already on when the button is pressed, it will go out.

2

Wait for the LED to flash indicating that the next digit can be entered.

3

Repeat the process for all four digits.

Summary of Contents for VSS3-Hilux



















Reviews: