Toyota SP100 Series Instruction Manual Download Page 40

Page: 40 / 54

At the tacking or the crease
that was ironed, fold back the
fabric so that wrong side faces
upward.

Sew overcasting along the edge of the fabric, and then fold the fabric as shown.

Tack or iron a crease 6 to 8 mm from the edge of the fabric.

Blind hem stitching

In this sewing method the stitch cannot be seen on the front of the fabric.

(For details on changing the presser foot, refer to “Changing the presser
foot” on page 24.)

Wrong

side

Wrong

side

Right

side

Right

side

Fold

(tacking or crease)

Wrong side

Caution

Before changing the presser foot, use the main power switch to turn

off the sewing machine.

Not doing so could result in injury.

Turn the handwheel toward you
until the needle is on the left side.

Needle on the left side

Zigzag sewing foot

Blind stitch foot

The blind stitch foot

is only included with

model SuperJ15 /

17 / SPJ17XL /

SUPERJEANS /

PowerFab17.

Overcasting

Change to the zigzag sewing foot or the blind stitch foot.

Tacking or crease

Overcasting

6 - 8 mm

15 stitch programmes

17 stitch programmes

Summary of Contents for SP100 Series























































Search results

Summary of Contents for SP100 Series

Reviews:

Related manuals for SP100 Series

Brands by name

Popular brands

Toyota SP100 Series, Instruction Manual

Search results

Summary of Contents for SP100 Series

Reviews:

Related manuals for SP100 Series

Brands by name

Popular brands