Toyota SP100 Series Instruction Manual Download Page 46

Page: 46 / 54

Changing light bulb

Turn the light bulb counterclockwise as
the arrow in the diagram and remove.

Turn the new light bulb clockwise to
install.

Note:

Use a light bulb with a maximum

power of 15 W.

The lamp can be purchased at

http://www.home-sewing.com.

Alternatively, contact your retailer.

Always reinstall the face cover after
replacing the light bulb.

Only use the lamp designed specifically for this sewing machine.

Not doing so could cause a fire.

Before changing the light bulb, use the main power switch to turn off

the sewing machine, remove the power plug from the outlet, and then

wait until the bulb cools.

Not doing so could cause a burn or electric shock.

Warning

Loosen the screw with a

screw driver of your

RZQDQGWDNHRႇWKHIDFH

cover in the direction of
the arrow.

Screw

Face cover

Summary of Contents for SP100 Series























































Search results

Summary of Contents for SP100 Series

Reviews:

Related manuals for SP100 Series

Brands by name

Popular brands

Toyota SP100 Series, Instruction Manual

Search results

Summary of Contents for SP100 Series

Reviews:

Related manuals for SP100 Series

Brands by name

Popular brands