background image

TOYOTA 

MY22 TUNDRA 

2022-  

DASHCAM 

(Digital Video Recorder) 

Preparation 

 

Page 1 of 14 pages 

Issue: B  11/19/2021 

 

 

Part Number:  PT949-34220 (Dashcam)  

Dashcam Kit Contents 

Item #  Quantity Reqd.  Description 

Dashcam Main Unit 

SD Card Holder 

SD Card (16 GB) 

Window Mounting Plate 

Foam Tape 

Cable Ties 

Quick Start Guide 

 

Additional Items Required For Installation 

Item #  Quantity Reqd.  Description 

PT949-34220 (Dashcam Unit) 

Conflicts 

N/A 

Recommended Tools 

Personal & Vehicle 

Protection 

Notes 

Seat Protection 

 

Dash Protection 

 

 

 

Special Tools 

Notes 

PT949-IAD0G 

Install Aid

 

For Port Installations Only 

 

 

Installation Tools 

Notes 

Panel Tool 

 

Socket Wrench 

With 10 mm Socket 

Torque Wrench 

With 10 mm Socket 

Hooked Panel Tool 

 

Needle Nose Pliers 

For Sun Visor Clip Removal 

 

 

Special Chemicals 

Notes 

VDC Approved Cleaner 

To Clean Windshield 

General Applicability 

All Models 

Recommended Sequence of Application 

Item #  Accessory 

Dashcam (PT949-34220) 

 

 

*Mandatory 

Vehicle Service Parts

 

(may be required for reassembly) 

Item #  Quantity Reqd.  Description 

Up to 2 pcs 

Roof Console Clips if damage 

occurs during removal. 

P/N: 90467-09240 

 

 

 

 

 

 

Kit Service Parts

 

(may be required in future) 

Item #  Part Number 

Description 

PT949-34220-AA 

Camera Unit + SD  

PT949-08210-AB

  SD Card 16GB Industrial 

PT949-08210-AC

  Sd Card Holder Assembly 

PT949-08210-AD

  Window Plate with Tape 

Legend 
 

 

STOP:

 Damage to the vehicle may occur.  Do not 

proceed until process has been complied with. 

OPERATOR SAFETY:

 Use caution to avoid risk of 

injury. 

CAUTION:

 A process that must be carefully observed 

in order to reduce the risk of damage to the 

accessory/vehicle and to ensure a quality installation. 

TOOLS & EQUIPMENT:

 Used in Figures calls out the 

specific tools and equipment recommended for this 

process. 

REVISION MARK:

 This mark highlights a change in 

installation with respect to previous issue. 

 

SAFETY TORQUE:

 This mark indicates that torque is 

related to safety. 

REGULATORY MARK:

 This mark indicates the 

component is related to regulatory compliance 

Summary of Contents for PT949-34220















Reviews: