background image

TOYOTA 

MY22 TUNDRA 

2022 -  

DASHCAM 

(Digital Video Recorder) 

Procedure 

 

Page 4 of 14 pages 

Issue: B  11/19/2021 

 

 

 

 

4.  Install Windshield Base Plate 

STOP: The front windshield must be        

at least 50°F (10°C). 

(a) For PPO Installations, please use 3D 

hard template with the part number 

“PT949-IAD0G”

 (Fig. 4-1) and follow 

steps (c) through (f). 

(b) For Dealer Installations or in the case 

that the 3D hard template is unavailable, 
please follow steps (g) through (i) 

(c) On the driver’s side of the vehicle, using 

window cleaner and a lint free cloth, 
clean the windshield area next to the 
TSS cover. 

(d) Insert the 3D Template (

PT949-IAD0G

between the TSS cover and the 
windshield glass on the driver’s side of 
the TSS cover, it should fit snugly 
against the TSS cover side walls, and 
the features of the template should allow 
it to stay in place hands free. If not, apply 
a small bit of tape for support to the 
lower edge. (Fig. 4-2) 

(e) Remove adhesive and stick mounting 

plate on windshield while aligning to the 
lower and right-side edges of the 
mounting plate. Press firmly to reduce 
visible air pockets. Note that the narrow 
end of the plate is towards the top of the 
windshield. (Fig. 4-3) 

(f)  Remove the 3D hard template by gently 

pulling towards the base of the 
windshield (wiper cowl area) to slide it 
out from under the TSS cover. (Fig. 4-4) 

 

 

Fig. 4-1 

  Fig. 4-2 

  Fig.4-4 

  Fig. 4-3 

Summary of Contents for PT949-34220















Reviews: