background image

TOYOTA 

MY22 TUNDRA 

2022 -  

DASHCAM 

(Digital Video Recorder) 

Procedure 

 

Page 6 of 14 pages 

Issue: B  11/19/2021 

 

 

6.  Remove Roof Map Light Console 

(a) Remove the roof console by pulling down 

firmly on the forward edge (towards the 
front of the vehicle). Pull down firmly to 
release front 2 clips first then slide 
forwards and downwards to release the 
tabs at the rear (towards the back of the 
vehicle) (Fig. 6-1) 
(1) A plastic panel removal tool may be 

used to pull down on the console. 

(2) CAUTION: Do 

not

 pry against the 

headliner or it will leave visible 
damage.  

(3) Note clips appearance in the image to 

better understand the removal 
process. (Fig. 6-2) 

(b) Once fully detached, disconnect the wire 

harness from the roof console and place 
the console in a safe place to avoid 
damage. (Fig. 6-2) 

(c) Inspect the console clips and replace if 

damaged (P/N: 90467-09240, 2 PCS) 

 

7.  Route Dashcam Harness through the 

Headliner 

 

(a) From the driver’s side of the windshield, 

locate the indention in the front edge of 
the headliner if available (Fig. 7-1)

 

 

 

 

(b) Route the Dash Cam pigtail through the 

indention or similar area, and into the 
headliner. Take care not to crease the 
headliner in the process. (Fig. 7-2) 
 

  Fig. 6-1 

  Fig. 6-2 

  Fig. 7-1 

  Fig. 7-2 

Summary of Contents for PT949-34220















Reviews: