background image

YW1838 

 

Penalty Time (Keypad Anti-Tamper Lockout Time)

 

Adjust Penalty Time 
Key Sequence 

[#] [Master Code] ● [92] ● [1-digit invalid codes entry] ● [1-digit X0 seconds] ●● 

 

For example,

 to adjust Penalty Time for 70 seconds after 5 invalid entries, press  

[#] [5555] ● [92] ● [5] ● [7] ●● 

 
Disable Penalty Time  
Key Sequence 

[#] [Master Code] ● [92] ● [0] ● [0] ●● 

 

Number of invalid User Codes can be programmed from 0 (disable) to 9. 

 

Penalty Time can be programmed from 10 seconds to 90 seconds, incremental in 10s (i.e. 9 = 90 seconds). 

 

Identify User ID 

Key Sequence 

[#] 

[Master Code] ● [09] ● [Enter Code to be located] ●● 

 
If the code entered is recognized, the following sequence will occur: 

 

At the start of the Code Location Function, the lock will flash both the green and red LEDs and emit 2 beeps. 

 

The lock will identify the first digit by flashing the green LED and beeping 0 

– 9 times. 

 

To signify the end of the first digit sequence, the lock will flash both the green and red LEDs and will emit 2 beeps. 

 

The lock will identify the second digit by flashing the green LED and beeping 0 

– 9 times. 

 

To signify the end of the second digit sequence, the lock will flash both the green and red LEDs and will emit 2 beeps. 

Should the code not be recognized, the lock will sound one long beep (0.5 sec) with a red LED. 

 

 
 
 

Summary of Contents for e-Smart 2000 Series













Reviews: