Toto TES1ADC-05 Installation Instructions Manual Download Page 15

(5) Attach the elbow to the front end of the air deflation

hose and attach it to the wall with the hose tie and

wood screw.
*Do not block the elbow. It is the air bleed point for

the system. The soap will not flow properly if the el-

bow is blocked.

Elbow

Air

Wood Screw

Hose tie

Air delflation hose

Be sure to install the elbow

between the top of the

sub-tank and the counter.

When the elbow is installed lower than the sub

tank the soap overflows.

Be sure that the hose tie is in position with the air

deflation hose and the elbow.

Caution

The total length of the connection hose is 
16.4’ (5 m). 

’ (5 m). 

liquid soap. 

To ensure sufficient supply performance, do 
not use a hose that is longer than 16.4
Please install the hose horizontally. 
(It is OK to place on the floor.) 

Install the hose in a straight line. 
A bent hose will prevent the smooth flow of 

Position the tanks on a level surface at even 
height. Installing the tanks at different levels 
may result in the following malfunctions: 

Soap leakage from the tank that is at a low-
er level. 

Improper detection of the liquid soap level 
in the tank at the higher level. 

Summary of Contents for TES1ADC-05

















Reviews: