Toto Link wireless N router User Manual Download Page 77

Page: 77 / 143

2.3 Panel Layout

2.3.1 Front Panel

The front panel of this router consists of 8 LEDs, which is designed to indicate connection
status.

POWER

This indicator lights blue when the router powered on, otherwise it is off.

CPU

This indicator blinks blue when router powered on.

WLAN

This indicator blinks blue when there are wireless devices connected and
transmitting data to the router.

When the WAN port is connected successfully the indicator lights blue.

Blink

During transmitting or receiving data through the WAN port the indicator
blinks blue.

WAN

Off

There is no device linked to the WAN port.

When the LAN port has a successful connection, the corresponding
indicator lights blue.

Blink

During transmitting or receiving data through the LAN port the
corresponding indicator blinks blue.

1/2/3/4

LAN

Off

There is no device linked to the LAN port.

2.3.2 Rear Panel

The figure below shows the rear panel of this router.

Summary of Contents for wireless N router
















































































































































Search results

Summary of Contents for wireless N router

Reviews:

Related manuals for wireless N router

Brands by name

Popular brands

Toto Link wireless N router, User Manual

Search results

Summary of Contents for wireless N router

Reviews:

Related manuals for wireless N router

Brands by name

Popular brands