Totalcomp TEI, Operation Manual

Page: 23 / 25

. 21 .
Symbol Symbol Symbol Symbol Definitions Definitions Definitions Definitions
CAP. CAP. CAP. CAP.---- ---- ---- - Next content displayed is Capacity SPL SPL SPL SPL.Lo .Lo .Lo .Lo - Sample load weight of low point.
CAL.ON CAL.ON CAL.ON CAL.ON - Calibration seal switch is in the ON position SPL SPL SPL SPL.HI .HI .HI .HI - Sample load weight of high point.
CAL.Px
CAL.Px CAL.Px
CAL.Px - Calibration on point(x) SPL
SPL SPL
SPL.PWT
.PWT .PWT
.PWT - Sample goods weight to calculate piece weight
CAL.End CAL.End CAL.End CAL.End - Calibration is finished INP INP INP INP.PCS .PCS .PCS .PCS - Input pieces number of weighted goods
COMP
COMP COMP
COMP - To go to input COMPARE data mode SPL
SPL SPL
SPL.PCT
.PCT .PCT
.PCT - Sample goods weight to calculate
HIGH HIGH HIGH HIGH - To input HIGH limitation data of Comparison INP INP INP INP.PCT .PCT .PCT .PCT - Input percentage of weighted goods
LOW LOW LOW LOW - To input LOW limitation data of Comparison AC.xxxx AC.xxxx AC.xxxx AC.xxxx - Accumulation instance is xxxx
PR PR PR PR.TARE .TARE .TARE .TARE - To Preset TARE weight
Troubleshooting
Troubleshooting Troubleshooting
Troubleshooting
SYMPTOM SYMPTOM SYMPTOM SYMPTOM PROBABLE PROBABLE PROBABLE PROBABLE CAUSE CAUSE CAUSE CAUSE REMEDY REMEDY REMEDY REMEDY
0
00
0
﹉﹉﹉﹉ ﹉﹉﹉﹉ ﹉﹉﹉﹉ ﹉﹉﹉﹉
Weight reading exceeds the Power On Zero limit
Make sure scale platform is empty. Perform zero
calibration.
0 00 0
﹍﹍﹍﹍ ﹍﹍﹍﹍ ﹍﹍﹍﹍ ﹍﹍﹍﹍
Weight reading is below the Power On Zero limit Install platform on scale. Perform zero calibration.
﹉﹉﹉﹉
﹉﹉﹉﹉ ﹉﹉﹉﹉
﹉﹉﹉﹉
Weight reading exceeds the overload limit or the weight
value can’t be displayed in the current unit of measure
because it exceeds 6 digits
Reduce load on scale until weight value can be
displayed or use an alternate unit of measure.
﹍﹍﹍﹍ ﹍﹍﹍﹍ ﹍﹍﹍﹍ ﹍﹍﹍﹍
Weight reading below minimum load limit Install platform on scale. Perform zero calibration.
EEP.E2 EEP.E2 EEP.E2 EEP.E2 USER parameters are not correctly set Re-set settings in USER mode
CAL.Er
CAL.Er CAL.Er
CAL.Er
Calibration error. Input data or loaded weight is too
small, too large, unstable, or not linear. Input correct data, load correct weight onto
platform, or service is required
PWT PWT PWT PWT.ER .ER .ER .ER
Piece weight error. The weight on the platform is too
small (<0.5d) to define a valid reference weight.
Use a greater weight for the sample
PCT
PCT PCT
PCT.ER
.ER .ER
.ER
Unit percentage weight error. The percentage weight
(1%, 0.1%, or 0.01%) is too small (<0.5d).
Use a greater weight for the sample
STB.ER STB.ER STB.ER STB.ER
Stabilization time USER-HOLD-STB.TIM is too short, or
Hold range USER-HOLD-HLD.RNG is too small, or other
failure
Set USER-HOLD-STB.TIM longer, or set
USER-HOLD-HLD.RNG larger, or service required
Won’t
Won’t Won’t
Won’t turn on
turn on turn on
turn on
Power cord not plugged in or properly connected.
Power outlet not supplying electricity.
Battery discharged. Other failure. Check power cord connections. Make sure power
cord is plugged into the power outlet. Check power
source. Replace batteries. Or service required.
Unable to Unable to Unable to Unable to zero the zero the zero the zero the
display
display display
display or will not zero
or will not zero or will not zero
or will not zero
when turned on
when turned on when turned on
when turned on
Load on scale exceeds allowable limits.
Load on scale is not stable.
Load cell damage. Remove load on scale.
Wait for load to become stable.
Service required.
Battery symbol is empty
Battery symbol is empty Battery symbol is empty
Battery symbol is empty
or Lo.bAt is shown
or Lo.bAt is shown or Lo.bAt is shown
or Lo.bAt is shown
Batteries are discharged Replace batteries