Total Source ELP15EULIT Operating Manual Download Page 11

11/44

Decal

Explanation

Reference

10

‘Emergency stop switch’ label.

166TA4115

11

‘Sling’ label.

Warning when lifting the pallet truck. Switch off 

the pallet truck and only lift it in unloaded 

condition.

Install the sling as indicated on the warning 

symbol.

166TA4120

3.2.  General safety instructions

•  Avoid fire hazards and have fire protection equipment present.

•  Do not use open pans of fuel or flammable cleaning fluids to clean parts.

•  Do not use open flames to check levers, or to check for leakages of electrolyte, 

fluids or oil.

•  The pallet truck needs to be kept in a clean condition to minimise fire hazards and 

facilitate detection of loose or defective parts.

•  The pallet truck may only be used by trained personnel.

•  The driver is responsible for the pallet truck during the time it is in use. He or she 

shall prevent unauthorised persons from driving or operating the pallet truck.

•  It is forbidden to carry passengers or lift people with the truck.

•  Any modification to the pallet truck assembly, in particular the safety mechanisms, 

is prohibited. The operational speeds of the pallet truck must not be changed 

under any circumstances.

•  The operator should read all warning signs and instructions in the manual and on 

the pallet truck before using it.

•  Do not exceed the maximum capacity.

•  The operator should wear safety shoes and gloves when using or maintaining the 

semi-electric pallet truck.

•  The pallet truck must not be used if it is damaged or when faults appear.

•  Do not use the pallet truck on a slope. It is designed to be used on even and level 

floors.

•  The weight of the goods should be distributed over the two forks, do not use only 

one fork. The centre of gravity of the goods should be in the centre of the two forks.

•  Be aware of hazardous situations like ledges or potholes, bumps and floor 

obstructions, debris, overhead obstructions and high-voltage conductors, 

inadequate surface support to withstand all load forces imposed by the machine.

•  The operator may not wear any loose objects, such as necklaces, rings, scarves … 

as they may become entangled in the machine and thus cause harm to the 

operator.

•  Do not operate a pallet truck unless you are of age. 

Summary of Contents for ELP15EULIT













































Reviews: