background image

Page 10

T

OTAL

C

ONTROL

MRX-8 S

YSTEM

C

ONTROLLER

EXCEPT AS EXPRESSLY PROVIDED FOR HEREIN, TECHNICAL

SERVICES ARE SUPPLIED "AS IS", WITHOUT ANY WARRANTY,

EXPRESS, STATUTORY OR IMPLIED, OF ANY KIND. TO THE

MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, URC

EXPRESSLY DISCLAIMS ALL WARRANTIES RELATING TO

TECHNICAL SERVICES, EXPRESS, STATUTORY OR IMPLIED,

INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF

QUALITY OR REASONABLE SKILL AND CARE, OR OUTCOME

OR RESULTS.

WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE

OTHER PROVISIONS HEREIN, THIS LIMITED WARRANTY DOES

NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT OR ACTS

OF NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH

THIRD PARTY CONTENT, OR (IV) BEYOND THE WARRANTY

PERIOD AND/ OR FAILURE TO FOLLOW URC WARRANTY

CLAIM PROCEDURE.

The warranty limitations and warranty disclaimers may not apply to

end user in whole or in part, where such are restricted or excluded

by applicable law, and such shall apply to the maximum extent

permitted by applicable law.

In the event of any warranty claim, URC will, at its sole option,

repair the URC equipment using new or comparable rebuilt parts,

or exchange the URC equipment for new or rebuilt equipment. 

In

the event of a defect, these are the end user's exclusive remedies.

All the URC equipment returned for service, exchange or repair

require an RGA number. To obtain an RGA number, you must

complete a Return Request Form which you may obtain by calling

(914) 835-4484 or contacting URC at

[email protected]. To obtain warranty service,

end user must deliver the URC equipment, freight prepaid, in its

original packaging or packaging affording adequate protection to

URC at 420 Columbus Avenue, Valhalla, NY 10595. It is end user's

responsibility to backup any macro programming, artwork, software

or other materials that may have been programmed into the unit. It

is likely that such data, software, or other materials will be lost

during service and URC will not be responsible for any such

damage or loss. A dated purchase receipt, bill of sale, installation

contract or other verifiable proof of purchase is required. For the

URC equipment support and other important information, please

visit URC's website available at www.universalremote.com or call

the Customer Service Center at (914) 835-4484.

This limited warranty only covers the URC equipment issues

caused by defects in material or workmanship during ordinary

consumer use. It does not cover product issues caused by any other

reason, including but not limited to product issues due to

commercial use, acts of God, third-party installation, misuse,

limitations of technology, or modification of or to any part of the

URC equipment. This limited warranty does not cover the URC

equipment sold as used, as is, refurbished, so called "B stock" or

consumables (such as batteries). This limited warranty is invalid if

the factory applied serial number has been altered or removed from

the URC equipment. 

This limited warranty specifically excludes

Summary of Contents for MRX-8




















Reviews: