Tosot TM09HSFDI Owner'S Manual Download Page 22

Page: 22 / 24

Multi Variable Air Conditioners Ducted Type Indoor Unit

(4) Check if any error code displayed after energized.

7.3 Maintenance after the Seasonal Use

(1) Set the unit in fan mode for half a day in a sunny day to dry the inner part of unit;
(2) When the unit won’t be used for a long time, please cut off power supply for energy saving;

the characters on the wired controller screen will disappear after cutting off the power
supply.

8 Table of Error Codes for Indoor Unit

Number

Error code

Error

Compressor high pressure protection

Indoor anti-freeze protection

Compressor low pressure protection, refrigerant lack

protection and refrigerant colleting mode

Compressor high discharge temperature protection

Communication error

Full water protection

Indoor ambient temperature sensor is open/short circuited

Indoor evaporator temperature sensor is open/short

circuited

Outdoor ambient temperature sensor is open/short

circuited

Outdoor condenser temperature sensor is open/short

circuited

Outdoor discharge temperature sensor is open/short

circuited

Loading EEPROM malfunction

Anti-high temperature protection

No feedback of indoor fan motor

Zero-crossing protection

Jumper cap malfunction protection

AC over-current protection

Mode conflict

Note: If there’re other error codes, please contact qualified professionals for service.

Summary of Contents for TM09HSFDI

























Search results

Summary of Contents for TM09HSFDI

Reviews:

Related manuals for TM09HSFDI

Brands by name

Popular brands

Tosot TM09HSFDI, Owner'S Manual

Search results

Summary of Contents for TM09HSFDI

Reviews:

Related manuals for TM09HSFDI

Brands by name

Popular brands