Tosot TM09HSFDI Owner'S Manual Download Page 5 | Manualshive

Page: 5 / 24

background image

Multi Variable Air Conditioners Ducted Type Indoor Unit

2

detergent to clean the outer casing of unit.

(26) If anything abnormal happens (such as burning smell), please power off the unit and cut off the main power
supply, and then immerdiately contact

TOSOT

appointed service center.If abnormality keeps going, the unit

might be damaged and lead to electric shock or fire.

Any personal injury or property loss caused by improper installation, improper debug,

unnecessary repair or not following the instructions of this manual should not be the responsibility

of

the local TOSOT agent.

«
...
3
4
5
6
7
...
»

Summary of Contents for TM09HSFDI

























Reviews:

No comments

Related manuals for TM09HSFDI

Brand: b-mola Pages: 16

Brand: Eaton-Williams Pages: 10

Brand: Samsung Pages: 14

Brand: Samsung Pages: 108

Brand: Samsung Pages: 16

Brand: Samsung Pages: 29

Brand: Samsung Pages: 16

Brand: Samsung Pages: 16

Brand: Samsung Pages: 14

Brand: Bard Pages: 33

Brand: Daikin Pages: 19

Brand: EdgeStar Pages: 19

CSF_HW_TUBE_R_R

Brand: Siga Pages: 14

smart Ultra-Air Mist AP9S

Brand: Momax Pages: 35

Brand: Daikin Pages: 12

R410A Split Series

Brand: Dakin Pages: 40

Brand: Danby Pages: 80

Brand: Carrier Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands