9
●
I FEEL
●
●
Notice
CLOCK
SLEEP
After starting up T-ON or T-OFF,set the constant cir-
culating valid.
After that,air conditioner will be turned on or turned off
according to setting time.ON/OFF button has no effect
on setting.If you don’t need this function, please use r-
emote controller to cancel it.
Clock time adopts 24-hour mode.
The interval between two operations can
'
t exceed 5s.
Otherwise, remote controller will quit setting status.
Operation for TIMER ON/TIMER OFF is the same.
Press this button to start I FEEL function and " "
will be displayed on the remote controller. After this
function is set, the remote controller will send the
detected ambient temperature to the controller
and the unit will automatically adjust the indoor te-
mperature according to the detected temperatu
re.
Press this button again to cancel I FEEL function
and " " will disappear.
Please put the remote controller near user when
this
function is set. Do not put the remote control
ler
near the object of high temperature or low temper-
ature in order to avoid detecting inaccurate amb
ie-
nt temperature.When I FEEL function is turned on,
the remote controller should be put within the a
rea
where indoor unit can receive the signal sent by
the
remote controller.
WiFi
●
Press this button, can select Sleep 1 ( 1),
Press this button to set clock time. " " icon on
remote controller will blink. Press "
▲
" or "
▲
"
button within 5s to set clock time. Each pressing
of "
▲
" or "
▲
" button, clock time will increas
e or
decrease 1 minute.If hold "
▲
" or "
▲
" button
, 2s
later, time will change quickly. Release this button
when reaching your required time. Press "CLOCK"
button to confirm the time. " " icon stops blinking.
●
Sleep 2 ( 2), Sleep 3 ( 3) and cancel the
Sleep, circulate between these, after electrified,
Sleep Cancel is defaulted.
Sleep 1 is Sleep mode 1, in Cool modes; sleep
setting temperature.
●
Sleep 2 is sleep mode 2, that is air conditioner
●
Sleep 3-the sleep curve setting under Sleep
will run according to the presetting a group of
sleep temperature curve.
status after run for one hour, the main unit setting
temperature will increase 1 , two hours, setting
temperature increased 2
℃
, then the unit will run at
this setting temperature; In Heat mode: sleep
status after run for one hour, the setting tempera-
ture will decrease 1 , two hours, setting tempera-
ture will decrease 2 , then the unit will run at this
When WiFi function is turned on, " WiFi " icon will
be displayed on the remote controller; when WiFi
function is turned off, " WiFi " icon will disappear.
How to turn on WiFi
：
Press " WiFi " button to turn
on WiFi function.
How to turn off WiFi
：
Hold " WiFi " button for 5s to
turn off WiFi function.
Under off status, press "MODE" and " WiFi " buttons
simultaneously for 1s, WiFi module will
restore factory settings.
This function is only available for some models.
●
Sleep3- the sleep curve setting under Sleep
mode by DIY could be inquired:
mode by DIY;
(1)Under Sleep 3 mode, press “Turbo” button for a
long time, remote controller enters into user indi-
viduation sleep setting status, at this time, the time
of remote controller will display “1hour”, the setting
temperature “88” will display the corresponding
temperature of last setting sleep curve and blink
(The first entering will display according to the
initial curve setting value of original factory);
(2)Adjust “+” and “-” button, could change the
corresponding setting temperature, after adjusted,
press “Turbo” button for confirmation;
(3) At this time, 1hour will be automatically
increased at the timer position on the remote con-
trol, (that are "2hours" or "3hours" or "8hours"), the
place of setting temperature "88" will display the
corresponding temperature of last setting sleep
curve and blink;
(4) Repeat the above step (2)~(3) operation, until
8 hours temperature setting finished, sleep,curve
setting finished, at this time, the remote controller
will resume the original timer display; temperature
display will resume to original setting temperature.
The user could accord to sleep curve setting
method to inquire the presetting sleep curve, enter
into user individuation sleep setting status, but do
not change the temperature, press "Turbo" button
directly for confirmation. Note: In the above preset-
ting or enquiry procedure, if continuously within
10s, there is no button pressed, the sleep curve
setting within 10s, there is no button pressed, the
sleep curve setting status will be automatically quit
and resume to display the original displaying. In
the presetting or enquiry procedure, press
"ON/OFF" button, "Mode" button, "Sleep" button,
the sleep curve setting or enquiry status will quit
similarly.
